Deutsch
EnglishDriving Aids for your Ford Focus 2018-2025
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Setting the Speed Limiter
INTELLIGENT SPEED LIMITER
- VEHICLES WITHOUT: LANE
Press the toggle button upward
or downward with the system in
CENTERING
Principle of Operation
standby mode to set the speed
limiter to the current vehicle
speed. The set speed is stored
and displayed in the information
display.
WARNING: When you are going
Note: The set speed limiter adjusts when
the system detects a different maximum
speed limit.
downhill, your vehicle speed could
increase above the set speed. The
system does not apply the brakes.
Note: If the system cannot detect a
maximum speed limit, the system returns
to standby mode.
You can adjust the set speed in small or
large increments. Press the toggle button
upward or downward once to adjust the
set speed in small increments. Press and
hold the toggle button upward or
downward to adjust the set speed in large
increments.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
The system allows you to limit the vehicle
speed to the maximum speed limit
detected by the speed sign recognition
system. For example, if the speed sign
recognition system detects a 80 km/h
(50 mph) speed limit, the vehicle speed is
limited to 80 km/h (50 mph). You can
temporarily exceed the set speed if
required, for example to overtake.
Note: The system does not limit the vehicle
speed to speed limits shown with a
supplementary traffic sign in the information
display.
Canceling the Set Speed
Press to cancel the set speed
limiter. The system returns to
standby mode.
Note: The speed limiter icon and the set
speed indicator are greyed out in standby
mode.
Note: The system does not limit the vehicle
speed in standby mode.
Resuming the Set Speed
Using Intelligent Speed Limiter
The controls are on the steering wheel.
Switching the System On or Off
Press to resume the set speed
limiter. The system sets the
speed limiter to the detected
maximum speed limit at the time it
resumes.
Press to switch the system on.
The system activates with the
detected speed-limit or, if no
speed-limit is detected, the current vehicle
speed as the set speed. Press again to
switch the system off.
317
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Intentionally Exceeding the Speed
Limit
Firmly press the accelerator pedal to
temporarily exceed the set speed limit. The
system resumes when the vehicle speed
drops below the set speed limit, or when
you press the RES button.
•
•
You intentionally exceed the set speed.
You unintentionally exceed the set
speed, for example when you are going
downhill. A tone also sounds.
Note: A tone sounds if you continue to
exceed the set speed.
Note: If the speed sign recognition system
detects a speed limit outside the
System Warnings
operational speed range, a tone sounds and
the system returns to standby mode.
A warning appears in the information
display if any of the following occur:
Adjusting Intelligent Speed
•
•
The vehicle speed exceeds the current
set speed.
The system detects a maximum speed
limit that is lower than the current
vehicle speed.
Limiter Tolerance Settings
You can set a permanent speed tolerance
that is in addition to the detected speed
limit through the tolerance menu in the
information display.
To adjust the speed tolerance setting, use the information display controls on
the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Tolerance
Press the OK button. Press the toggle button upward or
downward to choose your required speed setting. Press the
OK button.
SwitchingtoNormalSpeedLimiter
You can change between intelligent speed
limiter and normal speed limiter using the
information display. Intelligent speed
limiter allows you to limit the vehicle speed
to the maximum speed limit detected by
the speed sign recognition system. Normal
speed limiter allows you to manually limit
the vehicle speed using controls on the
steering wheel.
318
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
To switch between intelligent speed limiter and normal speed limiter, use the
information display controls on the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Note: If you switch intelligent speed limiter
off, the system defaults to manual speed
limiter. You can manually set the speed
limiter using the controls on the steering
wheel.
The system allows you to limit the vehicle
speed to the maximum speed limit
detected by the speed sign recognition
system. For example, if the speed sign
recognition system detects a 80 km/h
(50 mph) speed limit, the vehicle speed is
limited to 80 km/h (50 mph). You can
temporarily exceed the set speed if
required, for example to overtake.
Note: The system does not limit the vehicle
speed to speed limits shown with a
supplementary traffic sign in the information
display.
INTELLIGENT SPEED LIMITER
- VEHICLES WITH: LANE
CENTERING
Principle of Operation
Using Intelligent Speed Limiter
The controls are on the steering wheel.
Switching the System On or Off
WARNING: When you are going
downhill, your vehicle speed could
increase above the set speed. The
system does not apply the brakes.
Press to switch the system on.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
The system activates with the
detected speed-limit or, if no
speed-limit is detected, the current vehicle
speed as the set speed. Press again with
the system in standby mode to switch the
system off.
Setting the Speed Limiter
Press the toggle button upward
or downward with the system in
standby mode to set the speed
limiter to the current vehicle
speed. The set speed is stored
and displayed in the information
display.
319
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Note: The set speed limiter adjusts when
the system detects a different maximum
speed limit.
Note: If the system cannot detect a
maximum speed limit, the system returns
to standby mode.
You can adjust the set speed in small or
large increments. Press the toggle button
upward or downward once to adjust the
set speed in small increments. Press and
hold the toggle button upward or
downward to adjust the set speed in large
increments.
Intentionally Exceeding the Speed
Limit
Firmly press the accelerator pedal to
temporarily exceed the set speed limit. The
system resumes when the vehicle speed
drops below the set speed limit, or when
you press the RES button.
System Warnings
A warning appears in the information
display if any of the following occur:
•
•
The vehicle speed exceeds the current
set speed.
The system detects a maximum speed
limit that is lower than the current
vehicle speed.
Canceling the Set Speed
Press to cancel the set speed
limiter. The system returns to
standby mode.
•
•
You intentionally exceed the set speed.
You unintentionally exceed the set
speed, for example when you are going
downhill. A tone also sounds.
Note: The speed limiter icon and the set
speed indicator are greyed out in standby
mode.
Note: A tone sounds if you continue to
Note: The system does not limit the vehicle
exceed the set speed.
speed in standby mode.
Note: If the speed sign recognition system
Resuming the Set Speed
detects a speed limit outside the
operational speed range, a tone sounds and
the system returns to standby mode.
Press to resume the set speed
limiter. The system sets the
speed limiter to the detected
maximum speed limit at the time it
resumes.
Adjusting Intelligent Speed
Limiter Tolerance Settings
You can set a permanent speed tolerance
that is in addition to the detected speed
limit through the tolerance menu in the
information display.
320
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
To adjust the speed tolerance setting, use the information display controls on
the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Tolerance
Press the OK button. Press the toggle button upward or
downward to choose your required speed setting. Press the
OK button.
SwitchingtoNormalSpeedLimiter
You can change between intelligent speed
limiter and normal speed limiter using the
information display. Intelligent speed
limiter allows you to limit the vehicle speed
to the maximum speed limit detected by
the speed sign recognition system. Normal
speed limiter allows you to manually limit
the vehicle speed using controls on the
steering wheel.
To switch between intelligent speed limiter and normal speed limiter, use the
information display controls on the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Note: If you switch intelligent speed limiter
off, the system defaults to manual speed
limiter. You can manually set the speed
limiter using the controls on the steering
wheel.
321
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
The system calculates your alertness level
DRIVER ALERT
based upon your driving behavior in relation
to the lane markings and other factors
when the vehicle speed is greater than
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
approximately 65 km/h (40 mph).
Driver Alert System Warnings
The warning system has two stages:
1. A temporary warning is issued to advise
you to take a rest. This message only
appears for a short time.
2. If you do not rest and the system
continues to detect that your driving
deteriorates, it issues a further warning.
This remains in the information display
until you cancel it.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
WARNING: Take regular rest
breaks if you feel tired. Do not wait for
the system to warn you.
Note: The system does not warn you if the
vehicle speed falls below approximately
65 km/h (40 mph).
Driver Alert System Display
WARNING: Certain driving styles
may result in the system warning you
even if you are not feeling tired.
1. Using the information display controls
on the steering wheel, select Settings.
2. Select Information.
3. Select Driver alert.
WARNING: In cold and severe
weather conditions the system may not
function. Rain, snow and spray can all
limit sensor performance.
Your calculated alertness level is shown
by six steps as a colored bar. The bar
travels from right to left as your calculated
alertness level decreases.
WARNING: The system will not
operate if the sensor cannot track the
road lane markings.
WARNING:Ifdamageoccursinthe
immediate area surrounding the sensor,
have your vehicle checked as soon as
possible.
WARNING: The system may not
correctly operate if your vehicle is fitted
with a suspension kit not approved by
us.
E249476
Your calculated alertness level is good.
The system is designed to alert you if it
calculates that you are becoming drowsy
or if your driving deteriorates.
322
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Switching Driver Alert On and Off
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Switch Driver Alert on or off.
Note: The system remains on or off
depending on how it was last set.
E249477
Resetting Driver Alert
You can reset the system by:
Your calculated alertness level is low. You
should stop your vehicle and take a rest as
soon as it is safe to do so.
•
Switching the ignition off and on when
your vehicle is stationary.
Your calculated alertness level shows in
gray if:
•
Opening and closing the driver door
when your vehicle is stationary.
•
•
The sensor cannot track the road lane
markings.
The vehicle speed is less than
approximately 65 km/h (40 mph).
Driver Alert System Messages
Message
Action
Driver fatigue warning
Rest suggested
Displays when we recommend that you take a break due to
low alertness levels.
Driver fatigue warning
Rest now
Displays when you must take a break due to low alertness
levels.
WARNING: The sensor may
LANE KEEPING SYSTEM
incorrectly track lane markings as other
structures or objects. This can result in
a false or missed warning.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
WARNING: In cold and severe
weather conditions the system may not
function. Rain, snow and spray can all
limit sensor performance.
WARNING: Large contrasts in
outside lighting can limit sensor
performance.
WARNING: The system may not
function if the sensor is blocked.
323
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
The system may not correct lane
positioning in any of the following
WARNING: The system will not
conditions:
operate if the sensor cannot track the
•
•
•
•
High winds.
road lane markings.
Uneven road surfaces.
Heavy or uneven loads.
Incorrect tire pressure.
WARNING:Ifdamageoccursinthe
immediate area surrounding the sensor,
have your vehicle checked as soon as
possible.
Switching Lane Keeping System
On and Off
WARNING: The system may not
correctly operate if your vehicle is fitted
with a suspension kit not approved by
us.
The system is designed to alert you by
providing temporary steering assistance
or steering wheel vibration when it detects
an unintended lane departure. The system
detects and tracks the road lane markings
using a camera mounted behind the
interior mirror. The system only operates
when the vehicle speed is greater than
approximately 65 km/h (40 mph). You
can view the system status in the
E270719
Press the button on the direction indicator
stalk.
information display.
Note: The system works when the camera
can detect at least one lane marking or the
edge of the road.
Lane Keeping System Settings
The system has different settings that you
can view or adjust using the information
display.
Note: The system remembers the last
setting when you start your vehicle. If the
system detects a MyKey, the mode is set to
alert.
The system may not correctly operate in
any of the following conditions:
•
The system does not detect at least
one lane marking or the edge of the
road.
•
•
You switch the direction indicator on.
You apply direct steering, accelerate
Alert Mode
fast or brake hard.
Provides steering wheel vibration when the
system detects an unintended lane
departure.
•
•
•
The vehicle speed is less than 65 km/h
(40 mph).
The anti-lock brake, stability control or
traction control system activates.
Narrow lane width.
324
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Adjusting the Steering Wheel Vibration
Intensity
1. Using the information display controls
on the steering wheel, select Driver
assist..
Alert and Aid Mode
Provides temporary steering assistance
toward the lane center when the system
detects an unintended lane departure. If
your vehicle continues drifting out of the
lane, the steering wheel vibrates.
2. Select Lane keeping system.
3. Select Intensity.
4. Select a setting and press the OK
button.
Note: This setting does not affect the aid
mode.
Note: The system remembers the last
setting when you start your vehicle.
Adjusting the Lane Keeping System
Sensitivity
1. Using the information display controls
on the steering wheel, select Driver
assist..
E165517
A
B
Alert mode.
Aid mode.
2. Select Lane keeping system.
3. Select Sensitivity.
Note: The diagram illustrates general zone
coverage. It does not provide exact zone
parameters.
4. Select a setting and press the OK
button.
Aid Mode
Provides temporary steering assistance
toward the lane center when the system
detects an unintended lane departure.
Note: When aid mode is on and the system
does not detect any steering activity for a
short period of time, for example lightly
holding the steering wheel, the system alerts
you to put your hands on the steering wheel.
Note: The aid mode becomes active again
after you have returned your vehicle to the
center of the lane.
Switching the Lane Keeping System
Mode
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Lane keeping system.
3. Select Mode.
4. Select a setting and press the OK
button.
325
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
When the system is off, the system
Lane Keeping System Display
indicator or the lane markings do not
display.
Lane Keeping System Indicators
It illuminates in the information
display when you switch the
system on and Aid Mode or Alert
and Aid Mode are selected.
E
It illuminates in the information
display when you switch the
system on and Alert Mode is
selected.
Black and White Information Display
Indicator
System Status
Gray.
Unavailable.
Available.
White.
White and inverted.
White and flashing.
Temporary steering assistance.
Temporary steering assistance and steering wheel vibration.
Color Information Display
Indicator
Gray.
System Status
Unavailable.
Green.
Available.
Amber.
Temporary steering assistance.
Temporary steering assistance and steering wheel vibration.
Red.
Lane Keeping System Warning
Lamp
It could illuminate when you
switch the system off. If it
illuminates when you are driving,
this indicates a malfunction. Have your
vehicle checked as soon as possible.
326
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Lane Keeping System Messages
Message
Action
Lane keeping system
malfunction Service
required
The system has detected a fault that requires service. Have
your vehicle checked as soon as possible.
The system is designed to detect vehicles
that may have entered the blind spot zone.
BLIND SPOT INFORMATION
SYSTEM
The detection area is on both sides of your
vehicle, extending rearward from the
exterior mirrors to approximately 4 m
(13 ft) beyond the rear bumper. The
detection area extends to approximately
18 m (59 ft) beyond the rear bumper when
the vehicle speed is greater than 48 km/h
(30 mph) to alert you of faster
WARNING: Do not use the blind
spot information system as a
replacement for using the interior and
exterior mirrors or looking over your
shoulder before changing lanes. The
blind spot information system is not a
replacement for careful driving.
approaching vehicles.
Note: The system does not prevent contact
with other vehicles. It is not designed to
detect parked vehicles, pedestrians, animals
or other infrastructures.
WARNING: The system may not
operate properly during severe weather
conditions, for example snow, ice, heavy
rain and spray. Always drive with due
care and attention. Failure to take care
may result in a crash.
Using the Blind Spot Information
System
Vehicles with Automatic Transmission
The system turns on when all of the
following occur:
•
•
•
You start your vehicle.
You shift into drive (D).
The vehicle speed is greater than
10 km/h (6 mph).
Note: The system does not operate in park
(P) or reverse (R).
Vehicles with Manual Transmission
The system turns on when all of the
E255695
following occur:
•
•
You start your vehicle.
The vehicle speed is greater than
10 km/h (6 mph).
327
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Note: The system does not operate in
If you switch the system off, a warning
lamp illuminates and a message displays.
When you switch the system on or off, the
alert indicators flash twice.
reverse (R).
Blind Spot Information System
Sensors
Note: The system remembers the last
setting when you start your vehicle.
Note: The system may not correctly operate
when towing a trailer. For vehicles with a
trailer tow module and tow bar approved
by us, the system turns off when you attach
a trailer. For vehicles with an aftermarket
trailer tow module or tow bar, we
recommend that you switch the system off
when you attach a trailer.
E205199
To permanently switch the system off,
The sensors are behind the rear bumper
on both sides of your vehicle.
contact an authorized dealer.
Note: Keep the sensors free from snow, ice
Blind Spot Information System
Indicator
and large accumulations of dirt.
Note: Do not cover the sensors with bumper
When the system detects a
stickers, repair compound or other objects.
vehicle, an alert indicator
Note: Blocked sensors could affect system
illuminates in the exterior mirror
performance.
on the side the approaching vehicle is
coming from. If you turn the direction
indicator on for that side of your vehicle,
the alert indicator flashes.
If the sensors are blocked, a message may
appear in the information display. The alert
indicators remain illuminated but the
system does not alert you.
If the system detects a fault, an indicator
illuminates in the instrument cluster and
a message appears in the information
display. Have your vehicle checked as soon
as possible.
Note: The system may not alert you if a
vehicle quickly passes through the detection
zone.
Switching the Blind Spot
Information System On and Off
1. Using the information display controls
on the steering wheel, select Settings.
2. Select Driver assistance.
3. Switch BLIS on or off.
328
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Blind Spot Information System Information Messages
Message
Action
BLIS not available Sensor Displays if the blind spot information system sensors are
blocked See manual blocked.
BLIS deactivated Trailer Displays if you attach a trailer to your vehicle.
attached
BLIS malfunction
The system has detected a fault that requires service. Have
your vehicle checked as soon as possible.
The system is designed to alert you of
vehicles approaching from the sides behind
CROSS TRAFFIC ALERT
your vehicle when you shift into reverse
(R). If you continue to reverse after the
system alerts you, the system is designed
to apply the brakes if it still detects an
approaching vehicle. If the system applies
the brakes, a message appears in the
information display.
WARNING: Do not use the cross
traffic alert system as a replacement for
using the interior and exterior mirrors or
looking over your shoulder before
reversing out of a parking space. The
cross traffic alert system is not a
Note: The system does not apply the brakes
if you override it by firmly pressing the
accelerator pedal.
replacement for careful driving.
WARNING: The system may not
operate properly during severe weather
conditions, for example snow, ice, heavy
rain and spray. Always drive with due
care and attention. Failure to take care
may result in a crash.
Using Cross Traffic Alert
The system is designed to detect vehicles
that approach at a speed between 6 km/h
(4 mph) and 60 km/h (37 mph). Coverage
decreases when the sensors are partially,
mostly or fully obstructed. Slowly reversing
helps increase the coverage area and
effectiveness.
The system turns on when you start the
engine and you shift into reverse (R). The
system turns off when you shift out of
reverse (R).
329
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
E142440
The sensor on the left-hand side is only
partially obstructed and zone coverage on
the right-hand side is maximized.
330
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Zone coverage also decreases when
parking at narrow angles. The sensor on
the left-hand side is mostly obstructed and
zone coverage on that side is severely
reduced.
Note: Blocked sensors could affect system
performance.
If the sensors are blocked, a message may
appear in the information display when
you shift into reverse (R).
Cross Traffic Alert System Sensors
Cross Traffic Alert System
Limitations
The system may not correctly operate
when any of the following occur:
•
•
The sensors are blocked.
Adjacently parked vehicles or objects
are obstructing the sensors.
•
Vehicles approach at speeds less than
6 km/h (4 mph) or greater than
60 km/h (37 mph).
E205199
The sensors are behind the rear bumper
on both sides of your vehicle.
•
•
The vehicle speed is greater than
12 km/h (7 mph).
Note: Keep the sensors free from snow, ice
You reverse out of an angled parking
space.
and large accumulations of dirt.
Note: Do not cover the sensors with bumper
stickers, repair compound or other objects.
Switching Cross Traffic Alert On or Off
To switch cross traffic alert on or off, use the information display controls on the
steering wheel to select the following:
Menu Item
Driver assist.
Action
Press the menu button.
Cross traffic alert
Press the OK button.
Note: If you temporarily switch the system
off, it turns on the next time you switch the
ignition on.
To permanently switch the system off,
contact an authorized dealer.
Cross Traffic Alert Indicator
Note: The system may not correctly operate
when towing a trailer. For vehicles with a
trailer tow module and tow bar approved
by us, the system turns off when you attach
a trailer. For vehicles with an aftermarket
trailer tow module or tow bar, we
When the system detects an
approaching vehicle a tone
sounds, an indicator illuminates
in the relevant exterior mirror and arrows
appear in the information display to show
which side the approaching vehicle is
coming from.
recommend that you switch the system off
when you attach a trailer.
331
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Note: If arrows do not display, a message
Note: In exceptional conditions, the system
could alert you or apply the brakes, even
when there is nothing in the detection zone,
for example a vehicle passing further away
from your vehicle.
appears in the information display.
If the system malfunctions, an indicator
illuminates in the instrument cluster and
a message appears in the information
display. Have your vehicle checked as soon
as possible.
Cross Traffic Alert Information Messages
Message
Action
Cross traffic alert
Displays instead of indication arrows when the system
detects a vehicle. Check for approaching traffic.
Cross traffic not available Displays if the cross traffic alert system sensors are blocked.
Sensor blocked See
manual
Clean the sensors. If the message continues to appear, have
your vehicle checked as soon as possible.
Cross traffic malfunction The system has malfunctioned. Have your vehicle checked
as soon as possible.
Cross traffic alert deactiv- Displays if you attach a trailer to your vehicle.
ated Trailer attached
Cross traffic alert
Applying brakes
Displays if the system applies the brakes. Check for
approaching traffic.
The system is designed to detect traffic
signs to inform you of the current speed
TRAFFIC SIGN RECOGNITION
Principle of Operation
limit and overtaking regulations. Detected
traffic signs appear in the information
display. The sensor is behind the interior
mirror.
Note: Do not carry out windshield repairs
in the immediate area surrounding the
sensor.
Note: Traffic sign data provided by the
navigation system contains information
integrated to the data carrier release.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
The system detects recognizable traffic
signs, for example:
•
•
•
•
Speed limit signs.
No overtaking signs.
Speed limit cancellation signs.
No overtaking cancellation signs.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
332
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Note: The system may not detect all traffic
4. Select Activate speed warning.
5. Select Speed warning.
signs and may incorrectly read signs.
Note: In cold and severe weather conditions
the system may not function. Rain, snow,
spray and large contrasts in lighting can all
prevent the sensor from correctly
functioning.
Note: If your vehicle has a suspension kit
not approved by us, the system may not
correctly function.
6. Select a setting and press the OK
button.
Traffic Sign Recognition System
Display
Note: Always fit Ford original parts when
replacing headlamp bulbs. Other bulbs may
reduce system performance.
The system turns on when you switch the
ignition on and you cannot switch the
system off.
E132994
The system can display two traffic signs
in parallel.
Switching Speed Warning On and
Off
You can view the status at any time using
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Traffic sign recognition.
3. Select Activate Traff. Sign Recog..
4. Select Activate speed warning.
5. Switch Overspeed chime on or off.
the information display.
The system displays recognizable traffic
signs in four stages as follows:
1. All new traffic signs appear brighter
than the others in the display.
2. After a predetermined time they
display normally.
3. After a predetermined distance they
Setting the Speed Warning
are greyed out.
You can set the system speed warning to
alert you when the vehicle speed exceeds
the speed limit recognized by the system
by a certain speed tolerance.
1. Using the information display controls
on the steering wheel, select Driver
assist..
4. After another predetermined distance
they are deleted.
If the system detects a supplementary
traffic sign, it displays below the respective
traffic sign. For example, when passing a
reduced speed limit in wet road conditions
sign.
Note: If your vehicle has a navigation
system, stored traffic sign data may
influence the indicated speed limit value.
2. Select Traffic sign recognition.
3. Select Activate Traff. Sign Recog..
333
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Traffic Sign Recognition System Messages
Message
Action
Traffic sign recognition
Reduced performance
See manual
The traffic sign data provided by the navigation system is
unavailable due to weak or no signal. Wait for a short period
of time for the signal to improve. If the message continues
to appear, have your vehicle checked as soon as possible.
Note: In cold and severe weather conditions
the system may not function. Rain, snow,
SPEED SIGN RECOGNITION
Principle of Operation
spray and large contrasts in lighting can all
prevent the sensor from correctly
functioning.
Note: If your vehicle has a suspension kit
not approved by us, the system may not
correctly function.
Note: Always fit Ford original parts when
replacing headlamp bulbs. Other bulbs may
reduce system performance.
The system turns on when you switch the
ignition on and you cannot switch the
system off.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
Using Speed Sign Recognition
Switching Speed Warning On and Off
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Traffic sign recognition.
3. Select Activate Traff. Sign Recog..
4. Select Activate speed warning.
5. Switch Overspeed chime on or off.
The system is designed to detect speed
limit signs to inform you of the current
speed limit. Detected speed signs appear
in the information display. The sensor is
behind the interior mirror.
Note: Do not carry out windshield repairs
in the immediate area surrounding the
sensor.
Setting the System Speed Warning
Note: Speed sign data provided by the
navigation system contains information
integrated to the data carrier release.
You can set the system speed warning to
alert you when the vehicle speed exceeds
the speed limit recognized by the system
by a certain speed tolerance.
1. Using the information display controls
on the steering wheel, select Driver
assist..
Note: The system may not detect all speed
signs and may incorrectly read signs.
334
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
2. Select Traffic sign recognition.
3. Select Activate Traff. Sign Recog..
4. Select Activate speed warning.
5. Select Speed warning.
Speed Sign Recognition System
Display
6. Select a setting and press the OK
button.
Note: The system remembers the last
setting when you start your vehicle.
E318471
When the system detects a speed limit
sign, the speed limit appears in the
information display.
Note: If your vehicle has a navigation
system, stored speed sign data could
influence the indicated speed limit value.
Speed Sign Recognition System Messages
Message
Action
Traffic sign recognition
Reduced performance
See manual
The traffic sign data provided by the navigation system is
unavailable due to weak or no signal. Wait for a short period
of time for the signal to improve. If the message continues
to appear, have your vehicle checked as soon as possible.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
WRONG WAY ALERT
WARNING:The system is designed
to aid the driver. It is not intended to
replace your attention and judgment.
You are still responsible to drive with due
care and attention.
The system is designed to alert you if it
detects that you are driving the wrong way
on a freeway exit road. The system uses a
sensor behind the interior mirror to detect
no entry signs and uses information from
the navigation system.
Note: Do not carry out windshield repairs
in the immediate area surrounding the
sensor.
WARNING: At all times, you are
responsible for controlling your vehicle,
supervising the system and intervening,
if required. Failure to take care may result
in the loss of control of your vehicle,
serious personal injury or death.
335
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Note: Traffic sign data provided by the
navigation system contains information
integrated to the data carrier release.
If the system detects that you are driving
the wrong way on a freeway exit road, a
message appears in the information
display and a tone sounds. The audio
system volume mutes and navigation
system guidance pauses.
Note: In cold and severe weather conditions
the system may not function. Rain, snow,
spray and large contrasts in lighting can all
prevent the sensor from functioning
correctly.
Note: The system is designed to detect
traffic signs meeting the Vienna convention.
Note: The system may not detect all traffic
signs and may incorrectly read signs.
Note: If your vehicle has a suspension kit
not approved by us, the system may not
correctly function.
Note: Always fit Ford original parts when
replacing headlamp bulbs. Other bulbs may
reduce system performance.
Note: The system may not correctly operate
in areas under construction or new
infrastructure.
Note: The system does not operate in some
countries. We recommend that you check
system availability before use.
Note: In exceptional conditions, the system
could alert you even if you are not driving
the wrong way on a freeway exit road.
Switching Wrong Way Alert On or Off
To switch wrong way alert on or off, use the information display controls on the
steering wheel to select the following:
Menu Item
Driver assist.
Wrong way alert
Action
Press the menu button.
Press the OK button.
Note: The system remembers the last
setting when you start your vehicle.
Wrong Way Alert Information Messages
Message
Action
Check driving direction
The system has detected that you are driving the wrong way
on a freeway exit road. Press the OK button.
336
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Viewing the Instantaneous Efficiency
ECO
Level
Eco Mode
How Does Eco Mode Work
1. Using the information display controls
on the steering wheel, select MyView.
2. Select Eco coach.
The system is designed to monitor certain
driving characteristics to help you drive
more efficiently. See Driving
Trip Summary
The calculated trip summary is shown as
four colored bars. The bars travel from left
to right as the calculated efficiency levels
increase. The bars indicate the average
efficiency level for acceleration,
Economically (page 388).
Note: The efficiency levels do not result in
a defined fuel consumption figure. See Fuel
Consumption (page 221).
Note: The system only indicates the
efficiency level for the current trip. The
system resets each time you switch the
ignition on.
deceleration, speed and gear shifting
during the total distance traveled by your
vehicle for the current trip.
Note: Vehicles with an automatic
transmission do not have a bar for gear
shifting.
Instantaneous Efficiency Level
The display ring increases as the
instantaneous efficiency level increases
and illuminates when it reaches maximum
efficiency. The level continuously updates
to indicate the efficiency level for the
current trip.
Viewing the Trip Summary
1. Using the information display controls
on the steering wheel, select MyView.
2. Select Eco coach.
STEERING
Steering Information Messages
Message
Description
Steering assist malfunc- The system has malfunctioned. Stop your vehicle as soon
tion Service required
as it is safe to do so. You will continue to have full steering
but will need to exert greater force on the steering wheel.
Have your vehicle checked as soon as possible.
337
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
PRE-COLLISION ASSIST
unconventional vehicle types,
pedestrians or cyclists with complex
backgrounds, running pedestrians or fast
moving cyclists, partly obscured
WARNING: You are responsible for
pedestrians or cyclists, pedestrians or
cyclists that the system cannot
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
distinguish from a group. Failure to take
care may result in the loss of control of
your vehicle, personal injury or death.
WARNING:The Pre-Collision Assist
system with brake support cannot help
prevent all collisions. Do not rely on this
system to replace your judgment and the
need to maintain correct distance and
speed.
WARNING: The system does not
operate during hard acceleration or
steering. Failure to take care may lead
to a crash or personal injury.
The pre-collision assist system is active
when your vehicle reaches a speed greater
than approximately 5 km/h (3 mph).
Pedestrian and cyclist detection is active
at speeds up to 80 km/h (50 mph).
WARNING: The system may fail or
operate with reduced function during
cold and severe weather conditions.
Snow, ice, rain, spray and fog can
adversely affect the system. Keep the
front camera and radar free of snow and
ice. Failure to take care may result in the
loss of control of your vehicle, serious
personal injury or death.
Note: The system is not designed to detect
animals.
Note: The system is not designed to detect
vehicles that are traveling in a different
direction.
WARNING: The system may not
operate properly if your vehicle has a
non-Ford windshield. Do not carry out
windshield repairs in the area around the
sensor.
E156130
If your vehicle is rapidly approaching
another stationary vehicle, a vehicle
traveling in the same direction as yours, a
pedestrian or a cyclist within your driving
path, the system is designed to provide
three levels of functionality.
WARNING: System performance
could be reduced in situations where the
vehicle camera has limited detection
capability. These situations include but
are not limited to direct or low sunlight,
vehicles at night without tail lights,
338
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Level of Functionality
Alert
Description
When activated, a warning lamp flashes and an audible
warning sounds.
Brake support
The system is designed to help reduce the impact speed by
preparing the brakes for rapid braking. The system does not
automatically apply the brakes. If you press the brake pedal,
the system could apply additional braking up to maximum
braking force, even if you lightly press the brake pedal.
Active braking - vehicles The system is designed to apply the brakes if it detects a
without adaptive cruise crash is imminent. This may help reduce impact or avoid the
control
crash.
The system is active at speeds up to 130 km/h (80 mph).
Active braking - vehicles The system is designed to apply the brakes if it detects a
with adaptive cruise
control
crash is imminent. This may help reduce impact or avoid the
crash.
Setting the Distance Alert Sensitivity
1. Using the information display controls
on the steering wheel, select Driver
assist..
Switching Active Braking On and
Off
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Pre-collision Assist.
3. Switch Active braking on or off.
2. Select Pre-collision Assist.
3. Select Alert sensitivity.
4. Select a setting and press the OK
button.
Distance Alert (If Equipped)
Distance Indication (If Equipped)
A graphical indication displays the time
gap to vehicles ahead of you traveling in
the same direction.
Note: The graphic does not display if you
switch on cruise control or adaptive cruise
control.
A warning lamp illuminates if the distance
to the vehicle ahead is small.
Note: The warning lamp does not
illuminate if cruise control or adaptive cruise
control is active.
339
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Vehicle Speed System Sensit- Distance Indic-
Distance Gap
Time Gap
ivity
ator Color
Gray.
100 km/h
(62 mph)
Normal.
Greater than
Greater than 0.9
seconds.
25 m (82.0 ft) .
Yellow.
Red.
17–25 m
0.6-0.9
(55.8–82.0 ft).
seconds.
Less than 17 m
(55.8 ft).
Less than 0.6
seconds.
Note: If your vehicle sustains damage
leaving the sensors misaligned, this may
cause inaccurate measurements or false
alerts.
Blocked sensors could affect system
accuracy. A message may appear in the
information display.
Switching Distance Indication On and
Off
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Pre-collision Assist.
3. Switch Distance indication on or off.
Vehicles with Adaptive Cruise Control
Pre-Collision Assist System
Sensors
Vehicles without Adaptive Cruise
Control
E243054
The camera is mounted behind the interior
mirror.
E243054
The camera is mounted behind the interior
mirror.
Note: Keep the sensors free from snow, ice
and large accumulations of dirt.
Note: Do not clean the sensors with sharp
objects.
E244279
340
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
The radar sensor is behind the front grille
Pre-CollisionAssistWarningLamp
below the license plate.
It illuminates if your vehicle
Note: Keep the sensors free from snow, ice
rapidly approaches another
vehicle, to warn you of the risk of
and large accumulations of dirt.
a crash with the vehicle in front of you.
Note: Do not clean the sensors with sharp
objects.
It could illuminate red if the distance to the
vehicle ahead is small.
Note: If your vehicle sustains damage
leaving the sensors misaligned, this may
cause inaccurate measurements or false
alerts.
It illuminates when the system is not
available.
Blocked sensors could affect system
accuracy. A message may appear in the
information display.
Pre-Collision Assist Information Messages
Message
Action
Pre-collision assist not
available
The system has malfunctioned. Have your vehicle checked
as soon as possible.
Pre-collision assist not
The sensors are dirty. Clean the sensors. If the message
available Sensor blocked continues to appear, have your vehicle checked as soon as
possible.
The following table lists possible causes and actions for when a blocked sensor
message may display.
Cause
Action
The surface of the radar in the radiator grille Clean the radiator grille in front of the radar
is dirty or obstructed.
or remove any obstruction.
The surface of the radar is clean but the
message remains in the display.
Wait for a short period of time. It may take
several minutes for the system to detect
that there is no obstruction.
Heavy rain, spray, snow, or fog is interfering The system is temporarily disabled. The
with the radar signals.
system should reactivate after a short
period of time when the weather conditions
improve.
The radar is misaligned.
Have your vehicle checked as soon as
possible.
341
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Driving Aids - Vehicles With: 4.2 Inch Instrument Cluster Display
Screen
Cause
Action
The windshield in front of the camera is
dirty or obstructed.
Clean the outside of the windshield in front
of the camera.
The windshield in front of the camera is
clean but the message remains in the
display.
Wait for a short period of time. It may take
several minutes for the camera to detect
that there is no obstruction.
Excessive heat around the camera.
Wait for a short period of time. The
message should clear when the temper-
ature around the camera decreases.
Note: The system does not activate if the
distance to the vehicle ahead is too small
and a crash cannot be avoided.
Evasive Steering Assist(If Equipped)
If your vehicle is rapidly approaching a
stationary vehicle or a vehicle traveling in
the same direction as yours, the system is
designed to help you steer around the
vehicle.
Switching Evasive Steering Assist On
and Off
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Pre-collision Assist.
3. Switch Evasive steering on or off.
Note: Active braking and evasive steering
assist turn on each time you switch the
ignition on.
The system only activates when all of the
following occur:
•
Active braking and evasive steering
assist are switched on in the
information display.
•
•
The system detects a vehicle ahead
and starts to apply the brakes.
Note: If you turn active braking off, evasive
You significantly turn the steering
wheel in an attempt to steer around
the vehicle.
steering assist also turns off.
After you turn the steering wheel in an
attempt to avoid a crash with the vehicle
ahead, the system applies additional
steering torque to help you steer around
the vehicle. After you pass the vehicle, the
system applies steering torque when you
turn the steering wheel to steer back into
the lane. The system deactivates after you
fully pass the vehicle.
Note: The system does not automatically
steer around a vehicle. If you do no turn the
steering wheel, the system does not
activate.
342
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
