Deutsch
EnglishRoadside Emergencies for your Ford Focus 2018-2025
Roadside Emergencies
HAZARD FLASHERS
JUMPSTARTINGTHEVEHICLE
The hazard flasher switch is on
the instrument panel.
WARNING: Keep batteries out of
reach of children. Batteries contain
sulfuric acid. Avoid contact with skin,
eyes or clothing. Shield your eyes when
working near the battery to protect
against possible splashing of acid
solution. In case of acid contact with skin
or eyes, flush immediately with water for
a minimum of 15 minutes and get prompt
medical attention. If acid is swallowed,
call a physician immediately.
Use the hazard flashers if your vehicle is
creating a safety hazard for other road
users.
Switching the Hazard Flashers On
or Off
Press the button to switch the
hazard flashers on.
Press the button again to switch
WARNING: Batteries normally
produce explosive gases which can
cause personal injury. Therefore, do not
allow flames, sparks or lighted
the hazard flashers off.
Note: All direction indicators flash.
Note: Prolonged use of the hazard flashers
could cause the vehicle battery to run out
of charge.
Note: Depending on applicable laws in the
country your vehicle was built for, if you
heavily brake, the hazard flashers could turn
on.
substances to come near the battery.
When working near the battery, always
shield your face and protect your eyes.
Always provide correct ventilation.
WARNING: Use only adequately
sized cables with insulated clamps.
Hazard Flasher Indicator
Note: Do not disconnect the battery of the
disabled vehicle as this could damage the
vehicle electrical system.
Flashes when you switch the
hazard flashers on.
Connecting the Jumper Cables
FIRST AID KIT
The first aid kit can be stowed under the
front passenger seat or in the luggage
compartment.
Note: In the illustration, the bottom vehicle
represents the booster vehicle.
WARNING TRIANGLE
The warning triangle can be stowed under
the front passenger seat.
390
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Roadside Emergencies
4. Make the final connection of the
negative jumper cable to an exposed
metal part of the stalled vehicle's
engine, or connect the negative cable
to a ground connection point if
available.
1
3
4
2
E299202
WARNING:Do not connect the end
of the second cable to the negative (-)
terminal of the battery to be jumped. A
spark may cause an explosion of the
gases that surround the battery.
E142664
WARNING: Make sure that the
cables are clear of any moving parts and
fuel delivery system parts.
WARNING: Make sure that the
cables are clear of any moving parts and
fuel delivery system parts.
Park the booster vehicle close to the hood
of the disabled vehicle, making sure the
two vehicles do not touch.
Starting the Engine
Switch off the engine and any electrical
1. Start the engine of the booster vehicle
and press the accelerator gently to
keep the engine speed between 2000
and 3000 RPM.
equipment.
1. Connect the positive jumper cable to
the positive terminal of the discharged
battery.
2. Connect the other end of the positive
jumper cable to the positive terminal
of the assisting battery.
3. Connect the negative jumper cable to
the negative terminal of the assisting
battery.
2. Start the engine of the disabled vehicle.
3. Once the disabled vehicle has been
started, run both vehicle engines for an
additional three minutes before
disconnecting the jumper cables.
391
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Roadside Emergencies
Remove the jumper cables in the reverse
Rear Towing Point
order that they were connected.
Note: Do not switch the headlamps on
when disconnecting the cables. The peak
voltage could blow the bulbs.
TOWING POINTS
Front Towing Point
E265229
1. Gently press the top of the towing eye
attachment point cover inward.
2. Gently lift it upward and then pull it
straight out.
Note: The towing eye attachment point
cover has a small lanyard to keep it
attached to the bumper.
E265228
Attaching the Towing Eye
1. Gently press and release the towing
eye attachment point cover at the
position indicated.
WARNING: Make sure that the
towing eye is fully tightened. Failure to
follow this instruction could result in
personal injury.
2. Gently pull it straight out.
Note: The towing eye attachment point
cover has a small lanyard to keep it
attached to the bumper.
WARNING: You must switch the
ignition on when your vehicle is being
towed.
392
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Roadside Emergencies
E265230
1. Carefully remove the front or rear
towing eye attachment point cover.
2. Install the towing eye.
Note: It has a left-hand thread. Turn it
counterclockwise to install it.
Towing Eye Location
E265227
The towing eye is in the spare wheel
storage tray.
Note: You must carry the towing eye in your
vehicle at all times.
393
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
