Deutsch
EnglishInstrument Panel -> Gauges and Driver Information Interface for your Honda CR-V 2016-2021
Gauges and Driver Information Interface
Gauges
Gauges include the speedometer, fuel gauge, and other related indicators. They are
displayed when the power mode is in ON.
1Gauges
Press the
repeatedly until the
(display/information) button
icon is shown on the driver
hold it again. The speedometer reading and the
displayed measurements will switch between mph
and km/h.
Speedometer
■
Displays your driving speed in mph or km/h.
Fuel Gauge
■
1Fuel Gauge
Displays the amount of fuel left in the fuel tank.
NOTICE
You should refuel when the reading approaches
Running out of fuel can cause the engine to misfire,
damaging the catalytic converter.
E
.
POWER/CHARGE Gauge
■
■
Electric motor
The degree to which the electric motor is being powered is displayed by the readings
on the POWER side.
The actual amount of remaining fuel may differ from
the fuel gauge reading.
■
Battery charge in progress
The degree to which the High Voltage battery is being charged is displayed by the
readings on the CHARGE side.
124
uuGauges and Driver Information InterfaceuGauges
1High Voltage Battery Charge Level Gauge
High Voltage Battery Charge Level Gauge
■
The High Voltage battery charge level may decrease
under the following conditions:
Shows the remaining High Voltage battery charge level.
•
•
•
When the 12-volt battery has been replaced.
When the 12-volt battery has been disconnected.
When the High Voltage battery control system
corrects its reading.
The charge level reading will be corrected
automatically while driving.
Changes in the temperature of the High Voltage
battery can increase or decrease the battery’s
charging capacity. If temperature changes cause the
battery’s capacity to change, the number of
indicators in the battery charge level gauge may also
change, even if the amount of charge remains the
same.
125
uuGauges and Driver Information InterfaceuDriver Information Interface
Driver Information Interface
The driver information interface shows the odometer, trip meter, outside
temperature indicator, and other gauges.
It also displays important messages such as warnings and other helpful information.
Switching the Display
■
■
Main displays
Press the
(display/information) button, and then press
or
to change the
display. Press ENTER to see detailed information.
Eco Drive
Display
Power Flow
Monitor
Range &
Fuel
Average
Fuel
Economy
Records
Average
Speed &
Elapsed Time
Navigation*
& Compass*
Driver
Attention
Monitor
(Display/
Information)
Button
Warning
Messages
Customize*
Phone*
Audio*
Maintenance AWD Torque
MinderTM
Distribution
Monitor
Press
or
,
.
Speed Unit &
Disp OFF
Press ENTER.
* Not available on all models
126
uuGauges and Driver Information InterfaceuDriver Information Interface
■
Trip computer
Press the
(TRIP) knob to change display.
Odometer
Trip A
Trip B
Outside temperature
(TRIP)
Knob
Odometer
■
Shows the total number of miles or kilometers that your vehicle has accumulated.
1Trip Meter
Trip Meter
■
Switch between trip meter A and trip meter B by
pressing the
Shows the total number of miles or kilometers driven since the last reset. Meters A
and B can be used to measure two separate trips.
knob.
Continued
127
uuGauges and Driver Information InterfaceuDriver Information Interface
■
Resetting a trip meter
To reset a trip meter, display it, then press and hold the
knob. The trip meter is
reset to 0.0.
1Average Fuel Economy
Average Fuel Economy
■
You can change when to reset the average fuel
economy.
2 Customized Features P. 138, 366
Shows the estimated average fuel economy of each trip meter in mpg or l/100 km.
The display is updated at set intervals. When a trip meter is reset, the average fuel
economy is also reset.
Range
■
Shows the estimated distance you can travel on the remaining power and fuel. This
estimated distance is based on the vehicle’s current fuel economy.
1Elapsed Time
Elapsed Time
■
You can change when to reset the elapsed time.
2 Customized Features P. 138, 366
Shows the time elapsed since Trip A or Trip B was reset.
1Average Speed
Average Speed
■
You can change when to reset the average speed.
2 Customized Features P. 138, 366
Shows the average speed in mph or km/h since Trip A or Trip B was reset.
Instant Fuel Economy Gauge
■
Shows the instant fuel economy as a bar graph in mph or l/100 km.
128
uuGauges and Driver Information InterfaceuDriver Information Interface
Maintenance MinderTM
Shows the remaining oil life and Maintenance MinderTM.
2 Maintenance MinderTM P. 577
■
Average Fuel Economy Records
■
Shows the average fuel economy for the last
three driving cycles (1-3), and the current
driving cycle (0) in mpg or l/100 km.
Each time you set the power mode to ON, the
display is updated, and the oldest record is
deleted.
Continued
129
uuGauges and Driver Information InterfaceuDriver Information Interface
Eco Drive Display/Drive Cycle Score/Lifetime Points
■
■
Eco Drive Display
The vehicle icon on the display moves forward or backward while driving.
The more aggressive the acceleration is, the further the icon moves forward.
The more aggressive the deceleration is, the further the icon moves backward.
Keep the icon near the center of the circle for better fuel economy while driving.
Aggressive
Deceleration
Moderate
Slow
Moderate
Aggressive
Deceleration Acceleration/ Acceleration Acceleration
Deceleration
Vehicle Icon
130
uuGauges and Driver Information InterfaceuDriver Information Interface
■
Drive Cycle Score/Lifetime Points
Appear for a few seconds when you set the power mode to VEHICLE OFF. Each has
three stages. Depending on your driving style, the leaf icon(s) and the gauge
increase or decrease to indicate that you have reached a different stage of fuel
economy.
Advancing to
2nd Stage
Advancing to
3rd Stage
Drive Cycle
Score
Receding to
2nd Stage
Receding to
3rd Stage
Lifetime
Points
■
Resetting the Drive Cycle Score
1. Make sure the shift position is in (P. Turn the power mode to ON.
2. If ECON mode is on, press the ECON button to turn it off.
3. Turn the power mode to VEHICLE OFF.
4. Turn the power mode to ON again.
u Make sure to complete steps from 4 through 6 within 30 seconds.
5. Depress the brake pedal twice.
6. Press the ECON button twice.
u The color of the ambient meter will turn to monochrome.
7. Turn the power mode to VEHICLE OFF.
Continued
131
uuGauges and Driver Information InterfaceuDriver Information Interface
1Power Flow Monitor
Power Flow Monitor
■
While the vehicle is stationary with the engine
running, the following may appear on the driver
information interface.
Displays the power flow of the motor and engine, indicating the vehicle’s power
source and whether the battery is being charged.
Engine ON
Power Flow
Engine OFF
Engine
Hybrid (HV)
Electric Vehicle (EV)
Engine (Direct Drive)
Power is supplied by
the motor and the
engine.
Power is supplied by
the motor.
The engine is running
and the motor is charging
the High Voltage battery.
Regeneration
Power is being
supplied by only the
engine.
The engine is running
and the motor is
charging the High
Voltage battery.
The motor is charging
the High Voltage
battery.
132
uuGauges and Driver Information InterfaceuDriver Information Interface
1Driver Attention Monitor
Driver Attention Monitor
■
The Driver Attention Monitor cannot always detect if
the driver is tired or inattentive.
Regardless of the system's feedback, if you are
feeling tired, stop in a safe location and rest for as
long as needed.
The Driver Attention Monitor analyzes steering inputs to determine if the vehicle is
being driven in a manner consistent with drowsy or inattentive driving. If it
determines that the vehicle is being driven in such a manner, it will display the
degree of the driver's attention in the Driver Information Interface.
Driver Information Interface
ENTER
(Display/ Information) Button
When the
(display/information) button
is pressed, bars in the Driver Information
Interface light up in white to indicate the
degree of the driver's attention.
2 Switching the Display P. 126
Level
Continued
133
uuGauges and Driver Information InterfaceuDriver Information Interface
If two bars light up, the Driver Attention
Level Low message will appear.
If one bar lights up, the Driver Attention
Level Low. Time For A Break message will
appear, a beep will sound, and the steering
wheel will vibrate.
If this message appears, stop in a safe location
and rest for as long as needed.
The message will disappear when the ENTER
button is pressed or when the system has
determined that the driver is driving normally.
If the driver does not take a break and the
monitor continues to detect that the driver is
very tired, the message will appear again after
approximately 15 minutes, accompanied by a
beep and steering wheel vibrations.
The message does not appear when the
traveling time is 30 minutes or less.
134
uuGauges and Driver Information InterfaceuDriver Information Interface
■
The Driver Attention Monitor resets when
• the power system is turned off.
• the driver unfastens the seat belt and opens the door while the vehicle is stopped.
1For the Driver Attention Monitor to function
The bars in the Driver Information Interface remain
grayed out unless the Driver Attention Monitor is
functioning.
■
For the Driver Attention Monitor to function
• the vehicle must be traveling above 25 mph (40 km/h).
• the electric power steering (EPS) system indicator must be off.
■
Depending on driving conditions or other factors, the Driver Attention
Monitor may not function in the following circumstances.
• the steering assist function of the Lane Keeping Assist System (LKAS) is active.
2 Lane Keeping Assist System (LKAS) P. 530
• the condition of the road is poor, e.g. the surface is unpaved or bumpy.
• it is windy.
• the driver is frequently operating the vehicle in an assertive manner such as
■
Customizing
You can change the Driver Attention Monitor settings. Select Tactile And Audible
Alert, Tactile Alert, or OFF.
2 Customized Features P. 138, 366
Continued
135
uuGauges and Driver Information InterfaceuDriver Information Interface
AWD Torque Distribution Monitor
■
The indicators on the display show the
amount of torque being transferred to the
right front, left front, right rear, and left rear
wheels.
2 Real Time AWD with Intelligent Control
SystemTM P. 488
1Outside Temperature
Outside Temperature
■
The temperature sensor is in the front bumper.
Road heat and exhaust from another vehicle can
affect the temperature reading when your vehicle
Shows the outside temperature in Fahrenheit.
■
Adjusting the outside temperature display
Adjust the temperature reading by up to 5°F if the temperature reading seems
incorrect.
It may take several minutes for the display to be
updated after the temperature reading has stabilized.
You can adjust the temperature reading.
2 Customized Features P. 138, 366
136
uuGauges and Driver Information InterfaceuDriver Information Interface
1Navigation*
Navigation*
Compass*
■
■
You can select whether to have the turn-by-turn
display come on or not during the route guidance.
2 Customized Features P. 366
Shows the compass screen.
■
Turn-by-Turn Directions
When driving guidance is provided by the navigation system* or Android Auto, turn-
by-turn directions to your destination appear.
2 Refer to the Navigation System Manual
2 Android AutoTM P. 333
Audio*
■
Show the current audio information.
2 Audio System Basic Operation P. 268
Phone*
■
Show the current phone information.
2 Bluetooth® HandsFreeLink® P. 419
* Not available on all models
Continued
137
uuGauges and Driver Information InterfaceuDriver Information Interface
Models with color audio system
1Customized Features
Customized Features
■
To customize other features, press the
button.
3 4
/
Use the driver information interface to customize certain features.
2 List of customizable options P. 141
2 Example of customization settings P. 145
■
How to customize
Select the screen by pressing the
button while the power mode is in ON,
Put the transmission into (P before you attempt to
change any customized setting.
and the vehicle is at a complete stop, and the shift position is in (P. Select , then
press the ENTER button.
3
Button
Press to go back to the
previous display.
ENTER Button
Press to set your
selection.
4
Button
Button
Press to go to the next
display.
Press to go to Vehicle
Settings.
138
uuGauges and Driver Information InterfaceuDriver Information Interface
■
Customization flow
Press the button.
ENTER
Vehicle Settings
TPMS Calibration
3
4
Forward Collision Warning Distance
ACC Forward Vehicle Detect Beep
3
ENTER
Driver Assist System Setup
Road Departure Mitigation Setting
4
Lane Keeping Assist Suspend Beep
Driver Attention Monitor
3
4
Language Selection
Adjust Outside Temp. Display
“Trip A” Reset Timing
3
“Trip B” Reset Timing
Adjust Alarm Volume
ENTER
Meter Setup
4
Reverse Alert Tone
Fuel Efficiency Backlight
Speed/Distance Units
ENTER
3
4
3
4
Continued
139
uuGauges and Driver Information InterfaceuDriver Information Interface
3
4
3
4
Door Unlock Mode
Keyless Access Light Flash
Keyless Access Beep
3
4
ENTER
ENTER
Keyless Access Setup
Remote Start System ON/OFF
3
4
Interior Light Dimming Time
Headlight Auto OFF Timer
3
4
Lighting Setup
Auto Light Sensitivity
Auto Interior Illumination Sensitivity
Auto Headlight ON With Wiper ON
3
4
Auto Door Lock
Auto Door Unlock
3
4
Key And Remote Unlock Mode
Walk Away Auto Lock
Keyless Lock Answer Back
Security Relock Timer
ENTER
Door Setup
3
4
Maintenance Reset
3
4
Default All
3
4
ENTER
Exit
140
uuGauges and Driver Information InterfaceuDriver Information Interface
■
List of customizable options
Setup Group
Customizable Features
Description
Calibrates the TPMS.
Selectable Settings
Cancel/Calibrate
TPMS
Calibration
—
Forward Collision
Warning Distance
Changes the distance at which CMBSTM alerts.
Long/Normal*1/Short
ON/OFF*1
Causes the system to beep when the system detects
a vehicle, or when the vehicle goes out of ACC
range.
ACC Forward Vehicle
Detect Beep
Driver Assist
System
Setup
Road Departure
Mitigation Setting
Changes the setting for the road departure
mitigation system.
Narrow/Normal*1/Wide/
Warning Only
Lane Keeping Assist
Suspend Beep
Causes the system to beep when the LKAS is
suspended.
ON/OFF*1
Tactile And Audible Alert*1/
Tactile Alert/OFF
Driver Attention Monitor Changes the setting for the driver attention monitor.
*1:Default Setting
Continued
141
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Language Selection
Changes the displayed language.
English*1/Français/Español
Adjust Outside Temp.
Display
Adjusts the temperature reading by a few
degrees.
-5°F ~ 0°F*1 ~ +5°F
Changes the setting of how to reset trip meter
A, average fuel economy A, average speed A,
and elapsed time A.
When Fully Refueled/IGN OFF/
“Trip A” Reset Timing
“Trip B” Reset Timing
Manually Reset*1
Changes the setting of how to reset trip meter
B, average fuel economy B, average speed B,
and elapsed time B.
When Fully Refueled/IGN OFF/
Meter Setup
Manually Reset*1
Changes the alarm volume, such as buzzers,
warnings, turn signal sound, and so on.
Adjust Alarm Volume
Reverse Alert Tone
High/Mid*1/Low
ON*1/OFF
Causes the beeper to sound once when the
shift position is changed to (R
.
Fuel Efficiency Backlight
Speed/Distance Units
Turns the ambient meter feature on and off.
Selects the trip computer units.
ON*1/OFF
km/h∙km/mph∙miles*1
*1:Default Setting
142
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Changes which doors unlock when you grab the
driver’s door handle.
Door Unlock Mode
Driver Door Only*1/All Doors
Keyless Access Light
Flash
Causes some exterior lights to flash when you
unlock/lock the doors.
ON*1/OFF
Keyless
Access
Setup
Sets the beeper sound or not when you grab either
front door handle.
Keyless Access Beep
ON*1/OFF
Remote Start System
ON/OFF
Turns the remote engine start feature on and off.
ON*1/OFF
Interior Light Dimming
Time
Changes the length of time the interior lights stay on
after you close the doors.
60sec/30sec*1/15sec
Headlight Auto OFF
Timer
Changes the length of time the exterior lights stay
on after you close the driver’s door.
60sec/30sec/15sec*1/0sec
Max/High/Mid*1/Low/Min
Auto Light Sensitivity
Changes the timing for the headlights to come on.
Lighting
Setup
Changes the sensitivity of the brightness of the
instrument panel when the headlight switch is in the Max/High/Mid*1/Low/Min
AUTO position.
Auto Interior
Illumination Sensitivity
Changes the settings for the wiper operation when
the headlights automatically come on while the
headlight switch is in the AUTO position.
Auto Headlight ON With
Wiper ON
ON*1/OFF
*1: Default Setting
Continued
143
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Changes the setting for when the doors and the
tailgate automatically lock.
With Vehicle Speed*1/Shift
From P/OFF
Auto Door Lock
When Driver’s Door Opens*1/
When Shifting Into Park/
When Ignition Switched
OFF/OFF
Changes the setting for when the doors and the
tailgate automatically unlock.
Auto Door Unlock
Key And Remote Unlock
Mode
Sets up either the driver’s door or all doors to unlock
on the first operation of the remote.
Driver Door*1/All Doors
Door Setup
Changes the settings for the automatic locking the
doors when you walk away from the vehicle while
carrying the smart entry remote.
Walk Away Auto Lock
ON/OFF*1
Keyless Lock Answer
Back
LOCK/UNLOCK- The exterior lights flash.
LOCK (2nd push)- The beeper sounds.
ON*1/OFF
Changes the time it takes for the doors to relock and
the security system to set after you unlock the
vehicle without opening any door.
Security Relock Timer
90sec/60sec/30sec*1
Maintenance
Reset
Resets the Maintenance MinderTM display when you
have performed the maintenance service.
—
—
Cancel/All Due Items
Cancel/Set
Cancels customized changes you have made or
restores them to their default setting.
Default All
*1: Default Setting
144
uuGauges and Driver Information InterfaceuDriver Information Interface
■
Example of customization settings
The steps for changing the “Trip A” Reset Timing setting to When Fully Refueled
are shown below. The default setting for “Trip A” Reset Timing is Manually
Reset.
1. Press the
button to select , then
press the ENTER button.
3
4
2. Press the
/
button until Meter Setup
appears on the display.
3. Press the ENTER button.
u Language Selection appears first in the
display.
Continued
145
uuGauges and Driver Information InterfaceuDriver Information Interface
3
4
4. Press the
/
button until “Trip A”
Reset Timing appears on the display, then
press the ENTER button.
u The display switches to the
customization setup screen, where you
can select When Fully Refueled, IGN
OFF, Manually Reset, or Exit.
3
4
5. Press the
/
button and select When
Fully Refueled, then press the ENTER
button.
u The When Fully Refueled Setup screen
appears, then the display returns to the
customization menu screen.
3
4
6. Press the
/
button until Exit appears
on the display, then press the ENTER
button.
7. Repeat Step 6 until you return to the
normal screen.
146
