Deutsch
EnglishFeatures -> HomeLink Universal Transceiver for your Honda CR-V 2022-2025
HomeLink® Universal Transceiver*
1HomeLink® Universal Transceiver*
The HomeLink® Universal Transceiver can be programmed to operate up to three
remote controlled devices around your home, such as garage doors, lighting, or
home security systems.
Before programming HomeLink to operate a garage
door opener, confirm that the opener has an external
entrapment protection system, such as an “electronic
eye,” or other safety and reverse stop features. If it
does not, HomeLink may not be able to operate it.
Important Safety Precautions
■
Refer to the safety information that came with your garage door opener to test that
the safety features are functioning properly. If you do not have the safety
information, contact the manufacturer.
NOTE:
Some LED lightbulbs installed in the garage door
opener can interfere with the training and consistent
operation of your HomeLink device. Please consider
use of Low RF interference bulbs in your garage door
opener.
Before programming HomeLink, make sure that people and objects are out of the
way of the garage or gate to prevent potential injury or damage.
When programming a garage door opener, park just outside the garage door’s path.
* Not available on all models
395
uuHomeLink® Universal Transceiver*uTraining HomeLink
Training HomeLink
If it is necessary to erase a previously entered
learned code:
Red Indicator
• Press and hold the two outside buttons for
about 20 seconds, until the red indicator
blinks. Release the buttons, and proceed to
step 1.
• If you are training the second or third
button, go directly to step 1.
The instructions on the next page should work for most gate or garage openers, but
may not work for all. For detailed instructions about your specific remote opener,
396
uuHomeLink® Universal Transceiver*uTraining HomeLink
1Training HomeLink
Training a Button
■
Retraining a Button
1. Position the remote transmitter you wish to link 1 to 3 inches (3 - 8 cm) from the
If you want to retrain a programmed button for a
new device, you do not have to erase all button
memory. You can replace the existing memory code
using this procedure:
HomeLink button you want to program.
2.
Press and hold the desired HomeLink button. Hold the button on the remote
transmitter. Does the HomeLink indicator (LED) change from slowly blinking to
constantly on or rapidly blinking? The process should take less than 60 seconds.
1.
Press and hold the desired HomeLink button
until the HomeLink indicator begins to blink.
NO
NO
YES
Indicator remains on for about 25 secs.
Press and release the HomeLink button. Press
and release the button on the remote every 2
secs.
Does the HomeLink indicator (LED) change from
slowly blinking to constantly on or rapidly
blinking? The process should take less than 60
seconds.
3.
Press and hold the
programmed HomeLink
button for about a sec.
Does the device (garage
door opener) work?
2.
Quickly release the HomeLink button and follow
steps 1 - 3 under “Training a Button.” You do not
need to press and release the HomeLink button
again in step 2.
YES
Erasing Codes
YES
NO
To erase all the codes, press and hold the two outside
buttons until the HomeLink indicator begins to blink
(about 10 to 20 secs). You should erase all codes
before selling the vehicle.
4.
Press and hold the HomeLink button again.
Training
Complete
HomeLink indicator rapidly blinks.
HomeLink LED is
constantly on.
If you have any problems, see the device’s
HomeLink at (800) 355-3515.
A.
B.
The remote has a rolling code. Press the
“learn” button on the remote-controlled
device (e.g. garage door opener).
5.
Press and hold the HomeLink
button again.
The remote-controlled device
should operate.
HomeLink® is a registered trademark of Gentex
Corporation.
Within 30 secs, press and hold the
programmed HomeLink button for 2 secs.
Training Complete
397
