Deutsch
EnglishEase of use and comfort -> Front seats for your Peugeot 3008 2016-2023
Ease of use and comfort
When driving
Manually-adjusted seats
5. Lumbar support adjustment
3
(only on the driver's seat)
Maintain a good driving position and hold the
steering wheel with both hands at the 'quarter to
three' position, so that you can easily and quickly
reach the controls behind and near the steering
wheel.
► Turn the knob forwards or backwards
to increase or decrease the level of lumbar
support.
‘AGR’ certified seats
Additional adjustments
Never adjust the seats or steering wheel
when driving.
Always keep your feet on the floor.
Front seats
Before moving the seat backwards,
ensure that there is no person or object
that might prevent the full travel of the seat.
There is a risk of trapping or pinching
passengers if present in the rear seats or of
jamming the seat if large objects are placed
on the floor behind the seat.
1. Longitudinal adjustment of the seat position
► Raise the control bar and slide the seat
forwards or backwards.
1. Seat cushion length adjustment
► Pull the handle forwards to release the
cushion, then move the front part of the seat
cushion forwards or backwards.
2. Seat cushion angle electric adjustment
► Press and hold the front or rear of the
button to raise or lower the front part of the
seat cushion.
► Release the bar to lock the seat in
position in one of the notches.
2. Seat cushion height adjustment
► Raise or lower the control as many times
as needed to obtain the desired height.
3. Seat backrest angle adjustment
► Turn the knob forwards or backwards to
recline the backrest to the desired angle.
or
► For a passenger seat that can be placed
in the table position, pull the handle and
guide the backrest forwards or backwards.
4. Head restraint height adjustment
Refer to the corresponding section.
43
Ease of use and comfort
Folding the backrest
Front head restraints
3. Lumbar support electric adjustment
The control allows independent adjustment of
the depth and vertical position of the lumbar
support.
Adjusting the height
► Press and hold the front or rear of the
control to increase or reduce the lumbar
support.
► Press and hold the top or bottom of the
control to raise or lower the lumbar support
area.
Placing the passenger seat
in the table position
► Pull the control fully upwards to release the
backrest.
The backrest of the passenger seat can be fully
folded forwards and secured in this position.
This function, when associated with folding
of the backrest of the rear seats, helps with
transporting long and bulky objects.
First steps:
► Tip the backrest fully forwards.
Upwards:
► Pull the head restraint up to the desired
position; you can feel the head restraint clicking
into position.
Downwards:
► Press lug A to lower the head restraint.
In this position, the backrest can support
a maximum load of 30 kg.
When sharp deceleration occurs, objects
placed on the folded backrest can turn into
projectiles.
► Lower the head restraint.
► Fold up the “aircraft” type table (depending
on version).
► Move the seat backwards to allow space for
the head restraint.
► Adjust the seat to the lowest position.
► Check that there is nothing that might
interfere with folding of the backrest (seat belt,
child seat, items of clothing, bags, etc.).
The head restraint is correctly adjusted
when its upper edge is level with the top
of the head.
Returning the backrest into position
► Pull the control fully upwards to release the
backrest.
► Raise the backrest and guide it backwards
until it latches into place.
► Check that the backrest is correctly latched
into place.
Removing a head restraint
► Pull the head restraint fully up.
► Press lug A to release the head restraint and
raise it fully.
Deactivation of the front passenger
airbag is recommended.
► Stow the head restraint securely.
44
Ease of use and comfort
Refitting a head restraint
5. Lumbar support adjustment
3
► Insert the head restraint rods into the guides
in the corresponding seat backrest.
► Push the head restraint fully down.
► Press the lug A to release the head restraint
and push it down.
The control allows independent adjustment of
the depth and vertical position of the lumbar
support.
► Press and hold the front or rear of the
control to increase or reduce the lumbar
support.
► Adjust the height of the head restraint.
► Press and hold the top or bottom of the
control to raise or lower the lumbar support
area.
Never drive with the head restraints
removed; they should be in place and
adjusted for the occupant of the seat.
Memorising driving
positions
Associated with the electrically-adjusted driver’s
seat, this function allows two driving positions
to be memorised, to make these adjustments
easier if there are frequent driver changes.
It records the electric adjustments made to the
seat and door mirrors.
Electrically-adjusted driver's
seat
1. Seat cushion height and angle adjustment/
Longitudinal adjustment of the seat position
► Raise or lower the front of the control to
obtain the desired seat cushion angle.
► Raise or lower the rear of the control to
raise or lower the seat cushion.
► Slide the control forwards or backwards to
move the seat forwards or backwards.
2. Seat backrest angle adjustment
To carry out these electric adjustments,
switch on the ignition or start the engine
if the vehicle has gone into energy economy
mode.
These electric adjustments are accessible
about 1 minute after opening the driver's door.
They are deactivated about 1 minute after
switching the ignition off.
► Turn the control forwards or backwards to
recline the backrest to the desired angle.
3. Head restraint height adjustment
Refer to the corresponding section.
4. Seat cushion length adjustment
► Pull the handle forwards to release the
cushion, then move the front part of the seat
cushion forwards or backwards.
Using buttons M/1/2
45
Ease of use and comfort
► Enter the vehicle and switch the ignition on.
► Adjust your seat and the door mirrors.
► Press button M, then press button 1 or 2
within 4 seconds.
An audible signal confirms the memorisation.
Memorising a new position cancels the previous
position.
Prolonged use of heated seats is not
recommended for people with sensitive
Heated seats
skin.
There is a risk of burns for people whose
perception of heat is impaired (e.g. illness,
taking medication).
To keep the heated pad intact and to prevent
a short circuit:
Recalling a stored position
– Do not place heavy or sharp objects on the
seat.
– Do not kneel or stand on the seat.
– Do not spill liquids onto the seat.
– Never use the heating function if the seat
is damp.
While the seat is moving, take care that
no person or object hinders the
automatic movement of the seat.
The function is active only with the engine
running.
► Press the button corresponding to the seat.
► Each press changes the heating level; the
corresponding number of indicator lamps come
on.
► To switch off the heating, press the button
until all of the indicator lamps are off.
The system status is memorised when the
ignition is switched off.
With the ignition on or engine running
► Press button 1 or 2 to recall the
corresponding position.
An audible signal sounds when adjustment is
complete.
You can interrupt the current movement by
pressing button M, 1 or 2 or by using one of the
seat adjustment controls.
A stored position cannot be recalled while
driving.
Multipoint massage
System with a choice of type of massage and
adjustment of its intensity.
This system operates with the engine running, as
well as in STOP mode of the Stop & Start.
The massage settings are adjusted via the touch
screen.
Do not use the function when the seat
is not occupied.
Reduce the heating intensity as soon as
possible.
When the seat and passenger compartment
have reached a satisfactory temperature,
switch the function off; reducing electrical
consumption in turn decreases energy
consumption.
From the front seat:
The recalling of stored positions is deactivated
45 seconds after switching off the ignition.
► Press this button; its green indicator
lamp comes on.
The settings page is displayed on the touch
screen with the last memorised settings.
If the settings suit you and you make no
changes, the display returns to its previous state,
and the function activates immediately.
Seats must be adjusted one after another,
starting with the driver's seat.
46
Ease of use and comfort
To modify the settings:
► Adjust the height and reach to suit your
driving position.
► Push the control to lock the steering wheel.
Adjustment
3
► Begin with the driver’s seat.
► Select a massage intensity from the three
levels offered: "1" (Low), "2" (Normal) or "3"
(High).
► Select another type of massage from those
offered.
For safety reasons, these adjustments
must only be carried out with the vehicle
stationary.
► Wait for the driver's seat settings page to
disappear.
► Next, proceed with the passenger's seat in
the same way.
Mirrors
The changes are applied immediately.
Once activated, the system starts a one hour
massage cycle, made up of sequences of 6
minutes of massage followed by 3 minutes at
rest.
Door mirrors
► Move control A to the right or to the left to
select the corresponding mirror.
► Move control B in any of the four directions
to adjust.
As a safety measure, the mirrors should
be adjusted to reduce the "blind spots".
The objects that you see in the mirrors are
in fact closer than they appear. Take this
into account in order to correctly judge the
distance of vehicles approaching from behind.
The system automatically stops at the end of the
cycle; the indicator lamp for the button goes off.
► Return control A to its central position.
Manual folding
Steering wheel
adjustment
The mirrors can be folded manually (parking
obstruction, narrow garage, etc.).
► Turn the mirror towards the vehicle.
Demisting/Defrosting
The demisting/defrosting of the door
mirrors works with the demisting/
defrosting of the rear screen.
Electric folding
For more information on Rear screen
demisting/defrosting, refer to the
corresponding section.
Depending on equipment, the door mirrors can
be folded electrically.
► From the inside, with the
ignition on, place control A in the
central position.
► When stationary, pull the control to release
the steering wheel.
► Pull control A backwards.
► Lock the vehicle from the outside.
47
