Deutsch
EnglishDriving Aids for your Ford Fiesta 2017-2023
Driving Aids
You can adjust the set speed in small or
SPEED LIMITER
Principle of Operation
large increments. Press the toggle button
upward or downward once to adjust the
set speed in small increments. Press and
hold the toggle button upward or
downward to adjust the set speed in large
increments.
WARNING: When you are going
downhill, your vehicle speed could
increase above the set speed. The
system does not apply the brakes.
Canceling the Set Speed
Press to cancel the set speed
limiter. The system returns to
standby mode.
WARNING:The system is designed
to aid the driver. It is not intended to
replace your attention and judgment.
You are still responsible to drive with due
care and attention.
Resuming the Set Speed
Press to resume the set speed
The system allows you to set a speed to
which your vehicle becomes limited. The
set speed sets the effective maximum
speed of your vehicle. You can temporarily
exceed the set speed if required, for
example to overtake.
limiter.
Intentionally Exceeding the Speed
Limit
Firmly press the accelerator pedal to
temporarily exceed the set speed limit. The
system resumes when the vehicle speed
drops below the set speed limit, or when
you press the RES button.
Using Speed Limiter
The controls are on the steering wheel.
Switching the System On and Off
System Warnings
If you intentionally exceed the set speed,
a warning appears in the information
display.
If you unintentionally exceed the set speed,
for example when you are going downhill,
a warning appears in the information
display and a tone sounds.
Press to set the system in
standby mode. Press again to
switch the system off.
Setting the Speed Limiter
Press the toggle button upward
or downward with the system in
standby mode to set the speed
limiter to the current vehicle
speed. The set speed is stored
and displayed in the information
display.
INTELLIGENT SPEED LIMITER
Principle of Operation
WARNING: When you are going
downhill, your vehicle speed could
increase above the set speed. The
system does not apply the brakes.
185
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Note: The set speed limiter adjusts when
the system detects a different maximum
speed limit.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
Note: If the system cannot detect a
maximum speed limit, the system returns
to standby mode.
You can adjust the set speed in small or
large increments. Press the toggle button
upward or downward once to adjust the
set speed in small increments. Press and
hold the toggle button upward or
downward to adjust the set speed in large
increments.
The system allows you to limit the vehicle
speed to the maximum speed limit
detected by the speed sign recognition
system. For example, if the speed sign
recognition system detects a 80 km/h
(50 mph) speed limit, the vehicle speed is
limited to 80 km/h (50 mph). You can
temporarily exceed the set speed if
required, for example to overtake.
Canceling the Set Speed
Press to cancel the set speed
limiter. The system returns to
standby mode.
Note: The speed limiter icon and the set
speed indicator are greyed out in standby
mode.
Note: The system does not limit the vehicle
speed to speed limits shown with a
supplementary traffic sign in the information
display.
Note: The system does not limit the vehicle
speed in standby mode.
Using Intelligent Speed Limiter
The controls are on the steering wheel.
Switching the System On or Off
Resuming the Set Speed
Press to resume the set speed
limiter. The system sets the
speed limiter to the detected
maximum speed limit at the time it
resumes.
Press to switch the system on.
The system activates with the
detected speed-limit or, if no
speed-limit is detected, the current vehicle
speed as the set speed. Press again to
switch the system off.
Intentionally Exceeding the Speed
Limit
Firmly press the accelerator pedal to
temporarily exceed the set speed limit. The
system resumes when the vehicle speed
drops below the set speed limit, or when
you press the RES button.
Setting the Speed Limiter
Press the toggle button upward
or downward with the system in
standby mode to set the speed
limiter to the current vehicle
speed. The set speed is stored
and displayed in the information
display.
186
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
System Warnings
Note: A tone sounds if you continue to
exceed the set speed.
A warning appears in the information
Note: If the speed sign recognition system
display if any of the following occur:
detects a speed limit outside the
•
•
The vehicle speed exceeds the current
set speed.
The system detects a maximum speed
limit that is lower than the current
vehicle speed.
operational speed range, a tone sounds and
the system returns to standby mode.
Adjusting Intelligent Speed
Limiter Tolerance Settings
•
•
You intentionally exceed the set speed.
You can set a permanent speed tolerance
that is in addition to the detected speed
limit through the tolerance menu in the
information display.
You unintentionally exceed the set
speed, for example when you are going
downhill. A tone also sounds.
To adjust the speed tolerance setting, use the information display controls on
the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Tolerance
Press the OK button. Press the toggle button upward or
downward to choose your required speed setting. Press the
OK button.
SwitchingtoNormalSpeedLimiter
You can change between intelligent speed
limiter and normal speed limiter using the
information display. Intelligent speed
limiter allows you to limit the vehicle speed
to the maximum speed limit detected by
the speed sign recognition system. Normal
speed limiter allows you to manually limit
the vehicle speed using controls on the
steering wheel.
187
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
To switch between intelligent speed limiter and normal speed limiter, use the
information display controls on the steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Speed limiter
Intelligent
Note: If you switch intelligent speed limiter
off, the system defaults to manual speed
limiter. You can manually set the speed
limiter using the controls on the steering
wheel.
WARNING: In cold and severe
weather conditions the system may not
function. Rain, snow and spray can all
limit sensor performance.
WARNING: The system will not
operate if the sensor cannot track the
road lane markings.
DRIVER ALERT
WARNING:The system is designed
to aid the driver. It is not intended to
replace your attention and judgment.
You are still responsible to drive with due
care and attention.
WARNING:Ifdamageoccursinthe
immediate area surrounding the sensor,
have your vehicle checked as soon as
possible.
WARNING: The system may not
correctly operate if your vehicle is fitted
with a suspension kit not approved by
us.
WARNING: At all times, you are
responsible for controlling your vehicle,
supervising the system and intervening,
if required. Failure to take care may result
in the loss of control of your vehicle,
serious personal injury or death.
The system is designed to alert you if it
detects that you are becoming drowsy or
if your driving deteriorates. The system
calculates your alertness level based upon
your driving behavior in relation to the lane
markings and other factors when the
vehicle speed is greater than
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
approximately 65 km/h (40 mph).
WARNING: Take regular rest
breaks if you feel tired. Do not wait for
the system to warn you.
You can switch the system on or off using
the information display. See General
Information (page 91).
WARNING: Certain driving styles
may result in the system warning you
even if you are not feeling tired.
Note: The system remains on or off
depending on how it was last set.
188
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Your calculated alertness level is low. You
System Warnings
The warning system has two stages:
should stop your vehicle and take a rest as
soon as it is safe to do so.
1. A temporary warning is issued to advise
you to take a rest. This message only
appears for a short time.
2. If you do not rest and the system
continues to detect that your driving
deteriorates, it issues a further warning.
This remains in the information display
until you cancel it. See Information
Messages (page 95).
Your calculated alertness level shows in
gray if:
•
•
The sensor cannot track the road lane
markings.
The vehicle speed falls below
approximately 65 km/h (40 mph).
Resetting the System
You can reset the system by:
Note: The system does not warn you if the
vehicle speed falls below approximately
65 km/h (40 mph).
•
Switching the ignition off and on when
your vehicle is stationary.
•
Opening and closing the driver door
when your vehicle is stationary.
System Display
Your calculated alertness level is shown
by six steps as a colored bar. The bar
travels from right to left as your calculated
alertness level decreases.
LANE KEEPING SYSTEM
You can view the status at any time using
the information display. See General
Information (page 91).
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
WARNING: The system may not
function if the sensor is blocked.
E249476
WARNING: The sensor may
incorrectly track lane markings as other
structures or objects. This can result in
a false or missed warning.
Your calculated alertness level is good.
WARNING: In cold and severe
weather conditions the system may not
function. Rain, snow and spray can all
limit sensor performance.
E249477
189
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
•
•
The anti-lock brake, stability control or
traction control system activates.
Narrow lane width.
WARNING: Large contrasts in
outside lighting can limit sensor
performance.
The system may not correct lane
positioning in any of the following
conditions:
•
•
•
•
WARNING: The system will not
operate if the sensor cannot track the
road lane markings.
High winds.
Uneven road surfaces.
Heavy or uneven loads.
Incorrect tire pressure.
WARNING:Ifdamageoccursinthe
immediate area surrounding the sensor,
have your vehicle checked as soon as
possible.
Switching Lane Keeping System
On and Off
WARNING: The system may not
correctly operate if your vehicle is fitted
with a suspension kit not approved by
us.
The system is designed to alert you by
providing temporary steering assistance
or steering wheel vibration when it detects
an unintended lane departure. The system
detects and tracks the road lane markings
using a camera mounted behind the
interior mirror. The system only operates
when the vehicle speed is greater than
approximately 65 km/h (40 mph). You
can view the system status in the
E270719
Press the button on the direction indicator
stalk.
information display.
Note: The system works when the camera
can detect at least one lane marking or the
edge of the road.
Lane Keeping System Settings
The system has different settings that you
can view or adjust using the information
display.
Note: The system remembers the last
setting when you start your vehicle. If the
system detects a MyKey, the mode is set to
alert.
The system may not correctly operate in
any of the following conditions:
•
The system does not detect at least
one lane marking or the edge of the
road.
•
•
You switch the direction indicator on.
You apply direct steering, accelerate
Alert Mode
Provides steering wheel vibration when the
system detects an unintended lane
departure.
fast or brake hard.
•
The vehicle speed is less than 65 km/h
(40 mph).
190
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Adjusting the Steering Wheel Vibration
Alert and Aid Mode
Intensity
Provides temporary steering assistance
toward the lane center when the system
detects an unintended lane departure. If
your vehicle continues drifting out of the
lane, the steering wheel vibrates.
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Lane keeping system.
3. Select Intensity.
4. Select a setting and press the OK
button.
Note: This setting does not affect the aid
mode.
Note: The system remembers the last
setting when you start your vehicle.
Adjusting the Lane Keeping System
Sensitivity
1. Using the information display controls
on the steering wheel, select Driver
assist..
E165517
A
B
Alert mode.
Aid mode.
2. Select Lane keeping system.
3. Select Sensitivity.
Note: The diagram illustrates general zone
coverage. It does not provide exact zone
parameters.
4. Select a setting and press the OK
button.
Aid Mode
Provides temporary steering assistance
toward the lane center when the system
detects an unintended lane departure.
Note: When aid mode is on and the system
does not detect any steering activity for a
short period of time, for example lightly
holding the steering wheel, the system alerts
you to put your hands on the steering wheel.
Note: The aid mode becomes active again
after you have returned your vehicle to the
center of the lane.
Switching the Lane Keeping System
Mode
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Lane keeping system.
3. Select Mode.
4. Select a setting and press the OK
button.
191
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
When the system is off, the system
Lane Keeping System Display
indicator or the lane markings do not
display.
Lane Keeping System Indicators
It illuminates in the information
display when you switch the
system on and Aid Mode or Alert
and Aid Mode are selected.
E
It illuminates in the information
display when you switch the
system on and Alert Mode is
selected.
Black and White Information Display
Indicator
System Status
Gray.
Unavailable.
Available.
White.
White and inverted.
White and flashing.
Temporary steering assistance.
Temporary steering assistance and steering wheel vibration.
Color Information Display
Indicator
Gray.
System Status
Unavailable.
Green.
Available.
Amber.
Temporary steering assistance.
Temporary steering assistance and steering wheel vibration.
Red.
Lane Keeping System Warning
Lamp
It could illuminate when you
switch the system off. If it
illuminates when you are driving,
this indicates a malfunction. Have your
vehicle checked as soon as possible.
192
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Lane Keeping System Messages
Message
Action
Lane keeping system
malfunction Service
required
The system has detected a fault that requires service. Have
your vehicle checked as soon as possible.
The system is designed to detect vehicles
that may have entered the blind spot zone.
BLIND SPOT INFORMATION
SYSTEM
The detection area is on both sides of your
vehicle, extending rearward from the
exterior mirrors to approximately 4 m
(13 ft) beyond the rear bumper. The
detection area extends to approximately
18 m (59 ft) beyond the rear bumper when
the vehicle speed is greater than 48 km/h
(30 mph) to alert you of faster
WARNING: Do not use the blind
spot information system as a
replacement for using the interior and
exterior mirrors or looking over your
shoulder before changing lanes. The
blind spot information system is not a
replacement for careful driving.
approaching vehicles.
Note: The system does not prevent contact
with other vehicles. It is not designed to
detect parked vehicles, pedestrians, animals
or other infrastructures.
WARNING: The system may not
operate properly during severe weather
conditions, for example snow, ice, heavy
rain and spray. Always drive with due
care and attention. Failure to take care
may result in a crash.
Using the Blind Spot Information
System
Vehicles with Automatic Transmission
The system turns on when all of the
following occur:
•
•
•
You start your vehicle.
You shift into drive (D).
The vehicle speed is greater than
10 km/h (6 mph).
Note: The system does not operate in park
(P) or reverse (R).
Vehicles with Manual Transmission
The system turns on when all of the
E255695
following occur:
•
•
You start your vehicle.
The vehicle speed is greater than
10 km/h (6 mph).
193
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Note: The system does not operate in
If you switch the system off, a warning
lamp illuminates and a message displays.
When you switch the system on or off, the
alert indicators flash twice.
reverse (R).
Blind Spot Information System
Sensors
Note: The system remembers the last
setting when you start your vehicle.
Note: The system may not correctly operate
when towing a trailer. For vehicles with a
trailer tow module and tow bar approved
by us, the system turns off when you attach
a trailer. For vehicles with an aftermarket
trailer tow module or tow bar, we
recommend that you switch the system off
when you attach a trailer.
E205199
To permanently switch the system off,
The sensors are behind the rear bumper
on both sides of your vehicle.
contact an authorized dealer.
Note: Keep the sensors free from snow, ice
Blind Spot Information System
Indicator
and large accumulations of dirt.
Note: Do not cover the sensors with bumper
When the system detects a
stickers, repair compound or other objects.
vehicle, an alert indicator
Note: Blocked sensors could affect system
illuminates in the exterior mirror
performance.
on the side the approaching vehicle is
coming from. If you turn the direction
indicator on for that side of your vehicle,
the alert indicator flashes.
If the sensors are blocked, a message may
appear in the information display. The alert
indicators remain illuminated but the
system does not alert you.
If the system detects a fault, an indicator
illuminates in the instrument cluster and
a message appears in the information
display. Have your vehicle checked as soon
as possible.
Note: The system may not alert you if a
vehicle quickly passes through the detection
zone.
Switching the Blind Spot
Information System On and Off
1. Using the information display controls
on the steering wheel, select Settings.
2. Select Driver assistance.
3. Switch BLIS on or off.
194
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Blind Spot Information System Information Messages
Message
Action
BLIS not available Sensor Displays if the blind spot information system sensors are
blocked See manual blocked.
BLIS deactivated Trailer Displays if you attach a trailer to your vehicle.
attached
BLIS malfunction
The system has detected a fault that requires service. Have
your vehicle checked as soon as possible.
The system is designed to alert you of
vehicles approaching from the sides when
CROSS TRAFFIC ALERT
you shift into reverse (R).
Using the Cross Traffic Alert
System
WARNING: Do not use the cross
traffic alert system as a replacement for
using the interior and exterior mirrors or
looking over your shoulder before
reversing out of a parking space. The
cross traffic alert system is not a
The system is designed to detect vehicles
that approach with a speed up to 60 km/h
(37 mph). Coverage decreases when the
sensors are partially, mostly or fully
obstructed. Slowly reversing helps increase
the coverage area and effectiveness.
replacement for careful driving.
WARNING: The system may not
operate properly during severe weather
conditions, for example snow, ice, heavy
rain and spray. Always drive with due
care and attention. Failure to take care
may result in a crash.
The system turns on when you start the
engine and you shift into reverse (R). The
system turns off when you shift out of
reverse (R).
195
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
E142440
The sensor on the left-hand side is only
partially obstructed and zone coverage on
the right-hand side is maximized.
E142441
196
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Zone coverage also decreases when
Note: Keep the sensors free from snow, ice
parking at narrow angles. The sensor on
the left-hand side is mostly obstructed and
zone coverage on that side is severely
reduced.
and large accumulations of dirt.
Note: Do not cover the sensors with bumper
stickers, repair compound or other objects.
Note: Blocked sensors could affect system
System Lights, Messages and
Audible Alerts
performance.
If the sensors are blocked, a message may
appear in the information display when
you shift into reverse (R). See
Information Messages (page 95).
System Limitations
The system may not correctly operate
when any of the following occur:
•
•
The sensors are blocked.
Adjacently parked vehicles or objects
are obstructing the sensors.
•
•
•
Vehicles approach at speeds greater
than 60 km/h (37 mph).
E142442
When the system detects a vehicle, an
indicator illuminates in the exterior mirror
on the side the approaching vehicle is
coming from. A tone sounds and a
message appears in the information
display.
Note: In exceptional conditions, the system
could alert you even when there is nothing
in the detection zone, for example a vehicle
passing in the distance.
The vehicle speed is greater than
12 km/h (7 mph).
You reverse out of an angled parking
space.
System Errors
If the system detects a fault a message
displays. See General Information (page
91).
Switching the System Off and On
Blocked Sensors
You can temporarily switch the system off
using the information display. See General
Information (page 91). When you switch
system off, a message displays. See
Information Messages (page 95).
Note: The system turns on each time you
switch the ignition on and you shift into
reverse (R). If you temporarily switch the
system off, it turns on the next time you
switch the ignition on.
E205199
The sensors are behind the rear bumper
on both sides of your vehicle.
197
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Note: The system may not correctly operate
Note: Traffic sign data provided by the
navigation system contains information
integrated to the data carrier release.
when towing a trailer. For vehicles with a
trailer tow module and tow bar approved
by us, the system turns off when you attach
a trailer. For vehicles with an aftermarket
trailer tow module or tow bar, we
The system detects recognizable traffic
signs, for example:
•
•
•
•
Speed limit signs.
No overtaking signs.
Speed limit cancellation signs.
No overtaking cancellation signs.
recommend that you switch the system off
when you attach a trailer.
To permanently switch the system off,
contact an authorized dealer.
Note: The system may not detect all traffic
TRAFFIC SIGN RECOGNITION
Principle of Operation
signs and may incorrectly read signs.
Note: In cold and severe weather conditions
the system may not function. Rain, snow,
spray and large contrasts in lighting can all
prevent the sensor from correctly
functioning.
Note: If your vehicle has a suspension kit
not approved by us, the system may not
correctly function.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
Note: Always fit Ford original parts when
replacing headlamp bulbs. Other bulbs may
reduce system performance.
The system turns on when you switch the
ignition on and you cannot switch the
system off.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
Using Traffic Sign Recognition
Setting the System Speed Warning
You can set the system speed warning to
alert you when the vehicle speed exceeds
the speed limit recognized by the system
by a certain speed tolerance.
The system is designed to detect traffic
signs to inform you of the current speed
limit and overtaking regulations. Detected
traffic signs appear in the information
display. The sensor is behind the interior
mirror.
Note: Do not carry out windshield repairs
in the immediate area surrounding the
sensor.
198
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
To switch the system speed warning on or off, or to adjust the speed warning
settings, use the information display controls on the steering wheel to select the
following:
Menu Item
Driver assist.
Traffic sign recognition
Action
Press the menu button.
Press the OK button.
Activate speed warning Press the OK button.
Speed warning
Tolerance
Press the menu button.
Press the OK button. Press the toggle button upward or
downward to choose your required speed setting. Press the
OK button.
Overspeed chime
Press the OK button.
The system displays recognizable traffic
Traffic Sign Recognition System
Display
signs in four stages as follows:
1. All new traffic signs appear brighter
than the others in the display.
2. After a predetermined time they
display normally.
3. After a predetermined distance they
are greyed out.
4. After another predetermined distance
they are deleted.
If the system detects a supplementary
traffic sign, it displays below the respective
traffic sign. For example, when passing a
reduced speed limit in wet road conditions
sign.
Note: If your vehicle has a navigation
system, stored traffic sign data may
influence the indicated speed limit value.
E132994
The system can display two traffic signs
in parallel.
You can view the status at any time using
the information display.
199
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Traffic Sign Recognition System Messages
Message
Action
Traffic sign recognition
Reduced performance
See manual
The traffic sign data provided by the navigation system is
unavailable due to weak or no signal. Wait for a short period
of time for the signal to improve. If the message continues
to appear, have your vehicle checked as soon as possible.
Note: In cold and severe weather conditions
the system may not function. Rain, snow,
SPEED SIGN RECOGNITION
Principle of Operation
spray and large contrasts in lighting can all
prevent the sensor from correctly
functioning.
Note: If your vehicle has a suspension kit
not approved by us, the system may not
correctly function.
Note: Always fit Ford original parts when
replacing headlamp bulbs. Other bulbs may
reduce system performance.
The system turns on when you switch the
ignition on and you cannot switch the
system off.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
WARNING: The system may not
operate properly if the sensor is blocked.
Keep the windshield free from
obstruction.
Using Speed Sign Recognition
Setting the System Speed Warning
You can set the system speed warning to
alert you when the vehicle speed exceeds
the speed limit recognized by the system
by a certain speed tolerance.
The system is designed to detect speed
limit signs to inform you of the current
speed limit. Detected speed signs appear
in the information display. The sensor is
behind the interior mirror.
Note: The system remembers the last
setting when you start your vehicle.
Note: Do not carry out windshield repairs
in the immediate area surrounding the
sensor.
Note: Speed sign data provided by the
navigation system contains information
integrated to the data carrier release.
1. Using the information display controls
on the steering wheel, select Driver
assist..
2. Select Traffic sign recognition.
3. Select Activate Traff. Sign Recog..
4. Select Activate speed warning.
5. Select Speed warning.
Note: The system may not detect all speed
signs and may incorrectly read signs.
6. Select Tolerance.
7. Select a setting and press the OK
button.
200
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
When the system detects a speed limit
Speed Sign Recognition System
Display
sign, the speed limit appears in the
information display.
Note: If your vehicle has a navigation
system, stored speed sign data could
influence the indicated speed limit value.
E318471
Speed Sign Recognition System Messages
Message
Action
Traffic sign recognition
Reduced performance
See manual
The traffic sign data provided by the navigation system is
unavailable due to weak or no signal. Wait for a short period
of time for the signal to improve. If the message continues
to appear, have your vehicle checked as soon as possible.
Eco Mode System Display
You can view the instantaneous efficiency
level or the trip summary in the information
display.
ECO
Principle of Operation
The system is designed to monitor certain
driving characteristics to help you drive
more efficiently. See Economical Driving
(page 219).
Note: The efficiency levels do not result in
a defined fuel consumption figure. See Fuel
Consumption (page 146).
Note: The system only indicates the
efficiency level for the current trip. The
system resets each time you switch the
ignition on.
Instantaneous Efficiency Level
The display ring increases as the
instantaneous efficiency level increases
and illuminates when it reaches maximum
efficiency. The level continuously updates
to indicate the efficiency level for the
current trip.
To view the instantaneous efficiency level, use the information display controls
on the steering wheel to select the following:
Menu Item
MyView
Eco coach
Action
Press the menu button.
Press the OK button.
201
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Trip Summary
deceleration, speed and gear shifting
during the total distance traveled by your
vehicle for the current trip.
The calculated trip summary is shown as
four colored bars. The bars travel from left
to right as the calculated efficiency levels
increase. The bars indicate the average
efficiency level for acceleration,
Note: Vehicles with an automatic
transmission do not have a bar for gear
shifting.
To view the trip summary, use the information display controls on the steering
wheel to select the following:
Menu Item
MyView
Eco coach
Action
Press the menu button.
Press the OK button. Press it again to view the trip summary.
WARNING: The system may not
PRE-COLLISION ASSIST
operate properly if your vehicle has a
non-Ford windshield. Do not carry out
windshield repairs in the area around the
sensor.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in
the loss of control of your vehicle,
personal injury or death.
WARNING: In situations where the
vehicle camera has limited detection
capability, this may reduce system
performance. These situations include
but are not limited to direct or low
sunlight, vehicles at night without tail
lights, unconventional vehicle types,
pedestrians with complex backgrounds,
running pedestrians, partly obscured
pedestrians, or pedestrians that the
system cannot distinguish from a group.
Failure to take care may result in the loss
of control of your vehicle, serious
personal injury or death.
WARNING: The system does not
operate during hard acceleration or
steering. Failure to take care may lead
to a crash or personal injury.
WARNING: The system may fail or
operate with reduced function during
cold and severe weather conditions.
Snow, ice, rain, spray and fog can
adversely affect the system. Keep the
front camera and radar free of snow and
ice. Failure to take care may result in the
loss of control of your vehicle, serious
personal injury or death.
WARNING:The Pre-Collision Assist
system with brake support cannot help
prevent all collisions. Do not rely on this
system to replace your judgment and the
need to maintain correct distance and
speed.
202
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
The pre-collision assist system is active
when your vehicle reaches a speed greater
than approximately 5 km/h (3 mph).
Pedestrian detection is active at speeds
up to 80 km/h (50 mph).
E156130
If your vehicle is rapidly approaching
another stationary vehicle, a vehicle or
cyclist traveling in the same direction as
yours, or a pedestrian within your driving
path, the system is designed to provide
three levels of functionality.
Note: The system is not designed to detect
animals.
Note: The system is not designed to detect
vehicles or cyclists that are traveling in a
different direction.
Level of Functionality
Description
Alert
When activated, a warning lamp flashes and an audible
warning sounds.
Brake support
The system is designed to help reduce the impact speed by
preparing the brakes for rapid braking. The system does not
automatically apply the brakes. If you press the brake pedal,
the system could apply additional braking up to maximum
braking force, even if you lightly press the brake pedal.
Active braking - vehicles The system is designed to apply the brakes if it detects a
without adaptive cruise crash is imminent. This may help reduce impact or avoid the
control
crash.
The system is active at speeds up to 130 km/h (80 mph).
Active braking - vehicles The system is designed to apply the brakes if it detects a
with adaptive cruise
control
crash is imminent. This may help reduce impact or avoid the
crash.
To switch active braking on or off, use the information display controls on the
steering wheel to select the following:
Menu Item
Action
Driver assist.
Press the menu button.
Press the OK button.
Press the OK button.
Pre-collision Assist
Active braking
Note: The warning lamp does not
illuminate if cruise control or adaptive cruise
control is active.
Distance Alert (If Equipped)
A warning lamp illuminates if the distance
to the vehicle ahead is small.
203
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Distance Alert Sensitivity Settings
To adjust the distance alert sensitivity settings, use the information display
controls on the steering wheel to select the following:
Menu Item
Driver assist.
Action
Press the menu button.
Pre-collision Assist
Alert sensitivity
Press the OK button.
Press the OK button. Press the toggle button upward or
downward to choose your required setting. Press the OK
button.
Note: The graphic does not display if you
Distance Indication(If Equipped)
A graphical indication displays the time
gap to vehicles ahead of you traveling in
the same direction.
switch on cruise control or adaptive cruise
control.
Vehicle Speed System Sensit- Distance Indic-
Distance Gap
Time Gap
ivity
ator Color
Gray.
100 km/h
(62 mph)
Normal.
Greater than
Greater than 0.9
seconds.
25 m (82.0 ft) .
Yellow.
Red.
17–25 m
0.6-0.9
(55.8–82.0 ft).
seconds.
Less than 17 m
(55.8 ft).
Less than 0.6
seconds.
Switching Distance Indication On or Off
To switch distance indication on or off, use the information display controls on
the steering wheel to select the following:
Menu Item
Driver assist.
Action
Press the menu button.
Press the OK button.
Press the OK button.
Pre-collision Assist
Distance indication
204
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
The camera is mounted behind the interior
Pre-Collision Assist System
Sensors
mirror.
Vehicles without Adaptive Cruise
Control
E243054
E244279
The camera is mounted behind the interior
mirror.
The radar sensor is behind the front grille
below the license plate.
Note: Keep the sensors free from snow, ice
Note: Keep the sensors free from snow, ice
and large accumulations of dirt.
and large accumulations of dirt.
Note: Do not clean the sensors with sharp
Note: Do not clean the sensors with sharp
objects.
objects.
Note: If your vehicle sustains damage
leaving the sensors misaligned, this may
cause inaccurate measurements or false
alerts.
Blocked sensors could affect system
accuracy. A message may appear in the
information display.
Note: If your vehicle sustains damage
leaving the sensors misaligned, this may
cause inaccurate measurements or false
alerts.
Blocked sensors could affect system
accuracy. A message may appear in the
information display.
Vehicles with Adaptive Cruise Control
Pre-CollisionAssistWarningLamp
It illuminates if your vehicle
rapidly approaches another
vehicle, to warn you of the risk of
a crash with the vehicle in front of you.
It could illuminate red if the distance to the
vehicle ahead is small.
It illuminates when the system is not
available.
E243054
205
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Pre-Collision Assist Information Messages
Message
Action
Pre-collision assist not
available
The system has malfunctioned. Have your vehicle checked
as soon as possible.
Pre-collision assist not
The sensors are dirty. Clean the sensors. If the message
available Sensor blocked continues to appear, have your vehicle checked as soon as
possible.
The following table lists possible causes and actions for when a blocked sensor
message may display.
Cause
Action
The surface of the radar in the radiator grille Clean the radiator grille in front of the radar
is dirty or obstructed.
or remove any obstruction.
The surface of the radar is clean but the
message remains in the display.
Wait for a short period of time. It may take
several minutes for the system to detect
that there is no obstruction.
Heavy rain, spray, snow, or fog is interfering The system is temporarily disabled. The
with the radar signals.
system should reactivate after a short
period of time when the weather conditions
improve.
The radar is misaligned.
Have your vehicle checked as soon as
possible.
The windshield in front of the camera is
dirty or obstructed.
Clean the outside of the windshield in front
of the camera.
The windshield in front of the camera is
clean but the message remains in the
display.
Wait for a short period of time. It may take
several minutes for the camera to detect
that there is no obstruction.
Excessive heat around the camera.
Wait for a short period of time. The
message should clear when the temper-
ature around the camera decreases.
206
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Driving Aids
Trail
DRIVE CONTROL
Vehicle settings suited for driving
on unpaved roads.
Selectable Drive Modes
Your vehicle has various drive modes that
you can select for different driving
Track
conditions. Depending on the drive mode
that you select, the system adjusts various
vehicle settings, for example steering, gear
shifting, handling and powertrain response.
Vehicle settings suited for track
driving.
Note: Auto-start-stop switches off when
you select this mode.
Selecting a Drive Mode
The button is on the center console.
Note: Pre-Collision Assist is disabled when
you select this mode.
Repeatedly press the button to
Note: Lane Keeping System is disabled
scroll through the available drive
modes.
when you select this mode.
Note: Track mode is not intended for use
on public roads.
Note: Some drive modes cannot be
Note: Stability Control is adapted for track
selected when using a MyKey.
use when you select this mode.
Normal
Vehicle settings suited for
balanced driving.
Note:This is the default mode each time
you switch the ignition on.
Eco
Vehicle settings suited for
economical driving.
Slippery
Vehicle settings suited for driving
on slippery roads.
Sport
Vehicle settings suited for
sportier driving.
E
Note: Auto-start-stop switches off when
you select this mode.
207
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
