Deutsch
EnglishLighting for your Ford Fiesta 2017-2023
Lighting
GENERAL INFORMATION
LIGHTING CONTROL
Condensation in the Exterior Front
Lighting Control Positions
Lamps and Rear Lamps
Exterior front lamps and rear lamps have
vents to accommodate normal changes
in air pressure.
B
C
A
D
Condensation can be a natural by-product
of this design. When moist air enters the
lamp assembly through the vents, there is
a possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a fine mist
can form on the interior of the lens. The
fine mist eventually clears and exits
through the vents during normal operation.
Clearing time may take as long as 48 hours
under dry weather conditions.
Examples of acceptable condensation are:
•
The presence of a fine mist (no streaks,
E245649
drip marks or large droplets).
•
A fine mist covers less than 50% of the
lens.
A
B
Lamps off.
Parking lamps, instrument panel
Examples of unacceptable condensation
lamps and license plate lamps.
are:
•
•
C
D
Headlamps.
A water puddle inside the lamp.
Autolamps. See Autolamps
Streaks, drip marks or large droplets
(page 72).
present on the interior of the lens.
If you see any unacceptable condensation,
have your vehicle checked by an authorized
dealer.
On
1. Switch the ignition off.
2. Set the lighting control to the parking
lamps position.
Note: Parking lamps could turn off to
prevent the vehicle battery from running out
of charge.
Switching the Left-Hand Side or
the Right-Hand Side Parking
Lamps On(If Equipped)
1. Switch the ignition off.
70
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Flashing High Beam Headlamps
E242676
E248604
2. Push the lever up or down to switch the
parking lamps on.
Note: Parking lamps could turn off to
prevent the vehicle battery from running out
of charge.
Pull the lever toward you and release it to
flash the high beam headlamps.
High Beam Headlamp Indicator
It illuminates when you switch
Switching High Beam Headlamps
On and Off
the high beam headlamps on.
Lamps On Indicator
It illuminates when you switch
the low beam headlamps or the
side and rear lamps on.
Low Beam Headlamp Warning
Lamp (If Equipped)
If it illuminates when the low
beam headlamps are on, this
E248603
indicates that a low beam
headlamp bulb has failed.
Push the lever away from you to switch
the high beam headlamps on.
Push the lever forward again or pull the
lever toward you to switch the high beam
headlamps off.
Note: If you switch the autolamps on, you
cannot switch the high beam headlamps
on until the system turns the headlamps on.
Exterior Lamps On Audible
Warning
Sounds when you open the driver door and
the exterior lamps are on.
71
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Headlamps Information Messages
Message
Description
Check adaptive head-
lamps See manual
Displays if an electrical malfunction occurs with the headlamp
system. Have your vehicle checked as soon as possible.
Note: The headlamps turn off
approximately 60 seconds after you switch
the wipers off.
AUTOLAMPS
The headlamps remain on for a period of
time after you switch the ignition off. Use
WARNING: The system does not
the information display controls to adjust
the period of time that the headlamps
remain on.
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the headlamps on in low visibility
conditions, for example daytime fog.
Adjusting the Period of Time That
the Headlamps Remain On
1. Using the information display controls
Autolamps turn the headlamps on in low
light situations or when the wipers operate.
on the steering wheel, select Settings.
2. Select Vehicle settings.
3. Select Lighting.
4. Select Headlamp delay.
5. Select a setting.
6. Press the OK button.
INSTRUMENT LIGHTING
DIMMER
The instrument lighting dimmer buttons
are on the lighting control.
Repeatedly press one of the
buttons to adjust the brightness.
E253316
Note: When you switch the autolamps on,
the headlamps turn on within 10 seconds of
switching the wipers on.
Note: If you switch the autolamps and the
autowipers on, the headlamps turn on when
the windshield wipers continuously operate.
72
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
HEADLAMP EXIT DELAY
WARNING:Inspect and replace the
windshield wiper blades regularly to
make sure the camera sensor has a clear
view. The windshield wiper blades must
be the correct length.
After you switch the ignition off, you can
switch the headlamps on by pulling the
direction indicator lever toward you. You
will hear a short tone. The headlamps will
switch off automatically after three
minutes with any door open or 30 seconds
after the last door has been closed. You
can cancel this feature by pulling the
direction indicator toward you again or
switching the ignition on.
About Automatic High Beam
Control
The system is designed to turn the high
beams on if all of the following occur:
•
•
•
•
•
You switched the system on in the
information display.
AUTOMATIC HIGH BEAM
CONTROL
You set the lighting control to the
autolamps position.
The ambient light level is low enough
that high beams are required.
WARNING: The system does not
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the high beams on or off.
There is no traffic in front of your
vehicle.
Your vehicle speed is greater than
approximately 40 km/h (25 mph).
The system is designed to turn the high
WARNING: You may need to
override the system when approaching
other road users.
beams off if any of the following occur:
•
•
You switch the system off in the
information display.
WARNING: You may need to
override the system during inclement
weather.
You set the lighting control to any
position except autolamps.
•
•
You switch the rear fog lamps on.
WARNING: Do not use the system
in poor visibility, for example fog, heavy
rain, spray or snow.
The ambient light level is high enough
that high beams are not required.
•
•
The system detects an approaching
vehicle's headlamps or rear lamps.
WARNING: The system may not
switch the high beams off if the lights of
oncoming vehicles are hidden by
The system detects severe rain, snow
or fog.
obstacles, for example guard rails.
•
•
•
The system detects street lighting.
The camera has reduced visibility.
Your vehicle speed falls below
approximately 30 km/h (19 mph).
73
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Switching Automatic High Beam Control On or Off
To switch the system on or off, use the information display controls on the steering
wheel to select the following:
Menu Item
Settings
Action
Press the menu button.
Press the OK button.
Press the OK button.
Press the OK button.
Vehicle settings
Lighting
Auto highbeam
Automatic High Beam Indicator
Overriding Automatic High Beam
Control
It illuminates to confirm when
the system is ready to assist.
Push the lever away from you to switch
between high beam and low beam.
Automatic High Beam Control Information Messages
Message
Description
Front camera Low visib- The camera has reduced visibility. Clean the windshield. If
ility Clean screen
the message continues to appear, have your vehicle checked
as soon as possible.
Front camera temporarily The camera has malfunctioned. Wait a short period of time
not available
for the camera to cool down. If the message continues to
appear, have your vehicle checked as soon as possible.
You can switch the front fog lamps on if
any of the following occur:
FRONT FOG LAMPS
•
•
•
You set the lighting control to the
parking lamps position.
SwitchingtheFrontFogLampsOn
You set the lighting control to the
headlamps position.
You set the lighting control to the
autolamps position and the headlamps
are on.
or Off
Only switch the front fog lamps on during
reduced visibility.
The front fog lamp button is on the lighting
control.
Press the button to switch the
front fog lamps on or off.
74
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Note: The brightness of the daytime running
HEADLAMP LEVELING
lamps may decrease when the front fog
lamps are switched on.
To adjust the level of the headlamp
beams, do the following:
Front Fog Lamp Indicator
It illuminates when you switch
the front fog lamps on.
2
REAR FOG LAMPS
Switching the Rear Fog Lamps On
2
or Off
1
WARNING: Do not use the rear fog
lamps when it is raining or snowing and
visibility is more than 50 m (164.0 ft).
E132711
You can switch the rear fog lamps on if any
of the following occur:
1. Press to release the control.
•
•
You switched the front fog lamps on.
2. Rotate the control in accordance with
your vehicle load to prevent you from
distracting other road users when the
headlamps are on.
You set the lighting control to the
headlamps position.
•
You set the lighting control to the
autolamps position and the headlamps
are on.
Note: Set the control to zero when your
vehicle is unloaded.
Note: Set the headlamp beams to give
between 35–100 m (115–328 ft) of road
surface illumination when your vehicle is
partially or fully loaded.
The rear fog lamp button is on the lighting
control.
Press the button to switch the
rear fog lamps on or off.
3. Press to close the control.
Rear Fog Lamp Indicator
It illuminates when you switch
the rear fog lamps on.
75
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
CORNERING LAMPS
E72898
A
B
Headlamp beam.
Cornering lamp beam.
The cornering lamps illuminate the inside
of a corner when you are turning the
steering wheel.
DIRECTION INDICATORS
E242676
76
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Push the lever up or down to use
Switching the Rear Interior Lamps
On and Off
the direction indicators.
Note: Tap the lever up or down to make the
direction indicators flash three times.
INTERIOR LAMPS - VEHICLES
WITH:FRONTINTERIORLAMP
WITH MAP READING LAMPS
Switching All of the Interior Lamps
On and Off
E250958
Interior Lamp Function
E310027
E264886
When you set the switch to the middle
position, the interior lamps turn on if:
E310028
•
•
You open a door.
You press the unlock button on the
Switching the Front Interior Lamps
On and Off
remote control.
•
You switch the ignition off.
Note: If you switch the ignition off, the
interior lamps could turn off after a short
time to prevent the vehicle battery from
running out of charge.
E249791
Note: Press the edge of the lamps lens to
switch the front interior lamp off before
switching the ignition off to prevent the
vehicle battery from running out of charge.
77
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Lighting
Interior Lamp Function
INTERIOR LAMPS - VEHICLES
WITH:FRONTINTERIORLAMP
Switching All of the Interior Lamps
On and Off
When you set the switch to the middle
position, the interior lamps turn on if:
•
•
You open a door.
You press the unlock button on the
remote control.
•
You switch the ignition off.
Note: If you switch the ignition off, the
interior lamps could turn off after a short
time to prevent the vehicle battery from
running out of charge.
Switching the Rear Interior Lamps
On and Off
E309994
E309995
78
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
