Deutsch
EnglishMaintenance for your Ford Fiesta 2017-2023
Maintenance
Check Monthly
GENERAL INFORMATION
•
•
•
Engine oil level. See Engine Oil Check
(page 246).
WARNING: Do not work on a hot
engine.
WARNING: Switch the ignition off
and apply the parking brake.
•
•
•
•
•
Parking brake operation.
Horn operation.
WARNING: Do not touch the
electronic ignition system parts after you
have switched the ignition on or when
the engine is running. The system
operates at high voltage. Failure to
adhere to this warning could result in
serious personal injury or death.
Tightness of lug nuts. See Lug Nuts
(page 296).
OPENING AND CLOSING THE
HOOD
WARNING: Keep your hands and
clothing clear of the engine cooling fan.
Opening the Hood
Under certain conditions, the engine
cooling fan may continue to run for several
minutes after you switch your vehicle off.
See Engine Cooling Fan (page 248).
We recommend that you carry out the
following checks.
Check Daily
•
•
•
Exterior lamps.
Interior lamps.
Warning lamps and indicators.
E236610
Check When Refueling
1. Pull the hood release lever.
•
•
•
Washer fluid level. See Washer Fluid
Check (page 252).
(page 268).
236
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
2
3
E87786
5. Support the hood with the strut.
Closing the Hood
1. Remove the strut from the catch and
secure it correctly in the clip.
E236611
2. Lower the hood and allow it to drop
under its own weight for the last
20–30 cm (8–12 in).
2. Slightly lift the hood.
3. Release the hood latch by pushing the
secondary release lever to your
left-hand side.
Note: Make sure that the hood is correctly
closed.
4. Open the hood.
237
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.0L ECOBOOST™, LHD
A
B
C
D
E
F
H
G
E236612
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Engine oil dipstick. See Engine Oil Dipstick (page 246).
Air filter.
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
238
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.0L ECOBOOST™, RHD
A
B
C
D
E
F
H
G
E236613
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Brake fluid reservoir. See Brake Fluid Check (page 249).
Air filter.
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
239
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.1L DURATEC, LHD
A
B
C
D
E
F
H
G
E236614
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Engine oil dipstick. See Engine Oil Dipstick (page 246).
Air filter.
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
240
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.1L DURATEC, RHD
A
B
C
D
E
F
H
G
E236615
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Brake fluid reservoir. See Brake Fluid Check (page 249).
Air filter.
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
241
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.5L DURATORQ-TDCI DIESEL, LHD
A
B
C
D
E
H
G
F
E236618
A
B
C
D
E
Engine coolant reservoir. See Engine Coolant Check (page 248).
Engine oil filler cap. See Engine Oil Check (page 246).
Air filter.
F
G
H
Engine oil dipstick. See Engine Oil Dipstick (page 246).
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
242
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.5L DURATORQ-TDCI DIESEL, RHD
A
B
C
D
E
H
G
F
E236619
A
B
C
D
E
Engine coolant reservoir. See Engine Coolant Check (page 248).
Brake fluid reservoir. See Brake Fluid Check (page 249).
Air filter.
F
G
H
Engine oil dipstick. See Engine Oil Dipstick (page 246).
Windshield washer fluid reservoir. See Washer Fluid Check (page 252).
243
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.5L ECOBOOST™, LHD
A
B
C
D
E
F
H
G
E236616
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Engine oil dipstick. See Engine Oil Dipstick (page 246).
Air filter.
Windshield and rear window washer reservoir. See Washer Fluid Check (page
252).
244
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
UNDER HOOD OVERVIEW - 1.5L ECOBOOST™, RHD
A
B
C
D
E
F
H
G
E236617
A
B
C
D
E
F
G
H
Engine coolant reservoir. See Engine Coolant Check (page 248).
Brake fluid reservoir. See Brake Fluid Check (page 249).
Air filter.
Windshield and rear window washer reservoir. See Washer Fluid Check (page
252).
245
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
ENGINE OIL DIPSTICK - 1.0L
ECOBOOST™/1.1L DURATEC
ENGINE OIL DIPSTICK - 1.5L
ECOBOOST™
A
B
A
B
E264320
E141337
A
B
Minimum.
Maximum.
A
B
Minimum.
Maximum.
ENGINE OIL DIPSTICK - 1.5L
DURATORQ-TDCI DIESEL
ENGINE OIL CHECK
1. Make sure that your vehicle is on level
ground.
B
A
2. Check the oil level before starting the
engine, or switch the engine off and
wait 10 minutes for the oil to drain into
the oil pan.
3. Remove the dipstick and wipe it with
a clean, lint-free cloth. Reinstall the
dipstick and remove it again to check
the oil level.
E140423
If the oil level is at the minimum mark,
A
B
Minimum.
Maximum.
immediately add oil.
Note: Make sure that the oil level is
between the minimum and the maximum
marks.
Note: The oil consumption of new engines
reaches its normal level after approximately
5,000 km (3,000 mi).
246
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
3. Add engine oil that meets our
Adding Engine Oil
specifications. See Capacities and
Specifications (page 297).
4. Reinstall the engine oil filler cap. Turn
it clockwise until you feel a strong
resistance.
Note: Do not add oil further than the
maximum mark. Oil levels above the
maximum mark may cause engine damage.
WARNING: Do not add engine oil
when the engine is hot. Failure to follow
this instruction could result in personal
injury.
WARNING: Do not remove the filler
cap when the engine is running.
Note: Immediately soak up any oil spillage
with an absorbent cloth.
Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that may
not be covered by the vehicle Warranty.
OIL CHANGE INDICATOR
RESET
1. Clean the area surrounding the engine
oil filler cap before you remove it.
Only reset the system after changing the
2. Remove the engine oil filler cap.
engine oil and oil filter.
To reset the oil change indicator, use the information display controls on the
steering wheel to select the following:
Menu item
Action
Settings
Press the menu button.
Press the OK button.
Press the OK button.
Information
Oil life
Reset oil life
Press and hold the OK button until the system reset
confirmation appears.
247
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
ENGINE COOLING FAN -
GASOLINE
WARNING: Keep your hands and
clothing clear of the engine cooling fan.
Under certain conditions, the engine
cooling fan may continue to run for several
minutes after you switch your vehicle off.
ENGINE COOLING FAN -
DIESEL
WARNING: Keep your hands and
E170684
clothing clear of the engine cooling fan.
Make sure that the coolant level is
Under certain conditions, the engine
cooling fan may continue to run for several
minutes after you switch your vehicle off.
This could happen in low ambient
between the MIN and MAX marks on the
coolant reservoir at ambient temperature.
If the coolant level is at or below the
minimum mark, immediately add coolant.
temperatures and independent of the
engine coolant temperature, for example
short journeys or low coolant temperature.
See Diesel Particulate Filter (page 150).
The coolant concentration should be
maintained within 48% to 50%, which
equates to a freeze point between -34°C
(-29°F) and -37°C (-35°F).
Note: Coolant expands when it is hot. The
ENGINE COOLANT CHECK
level may extend beyond the MAX mark.
Note: Do not use stop leak pellets, cooling
system sealants, or non-specified additives
as they can cause damage to the engine
cooling or heating systems.
WARNING: Do not dispose of
coolant in the household refuse or the
public sewage system. Use an authorized
waste disposal facility.
WARNING: Do not put coolant in
the windshield washer reservoir. If
sprayed on the windshield, coolant could
make it difficult to see through the
windshield.
248
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
In case of emergency, you can add water
Adding Coolant
without engine coolant in order to reach a
vehicle service location.
WARNING: Do not remove the
Note: Prolonged use of an incorrect dilution
of coolant can cause damage, for example
corrosion, overheating or freezing.
coolant reservoir cap when the engine is
on or the cooling system is hot. Wait 10
minutes for the cooling system to cool
down. Cover the coolant reservoir cap
with a thick cloth to prevent the
BRAKE FLUID CHECK
possibility of scalding and slowly remove
the cap. Failure to follow this instruction
could result in personal injury.
WARNING: Do not use any fluid
other than the recommended brake fluid
as this will reduce brake efficiency. Use
of incorrect fluid could result in the loss
of vehicle control, serious personal injury
or death.
WARNING: Do not allow the fluid
to touch your skin or eyes. If this
happens, rinse the affected areas
immediately with plenty of water and
contact your physician.
WARNING: Only use brake fluid
from a sealed container. Contamination
with dirt, water, petroleum products or
other materials may result in brake
system damage or failure. Failure to
adhere to this warning could result in the
loss of vehicle control, serious personal
injury or death.
WARNING: Undiluted coolant is
flammable and may ignite if spilled on a
hot exhaust.
We do not recommend the use of recycled
engine coolant since a Ford-approved
recycling process is not yet available.
Do not mix different colors or types of
WARNING: Do not allow the fluid
to touch your skin or eyes. If this
happens, rinse the affected areas
immediately with plenty of water and
contact your physician.
coolant in your vehicle.
Note: Add a 50/50 mixture of antifreeze
and water or prediluted engine coolant that
meets the correct specification.
Note: Use fluids which meet the
WARNING: A fluid level between
the MAX and MIN lines is within the
normal operating range and there is no
need to add fluid. A fluid level not in the
normal operating range could
specifications or requirements defined. Use
of other fluids may lead to damage which
is not covered by the vehicle Warranty. See
Capacities and Specifications (page 297).
To top up the coolant level do the
compromise the performance of the
system. Have your vehicle checked
immediately.
following:
1. Remove the coolant reservoir cap.
2. Add coolant to the MAX mark, do not
overfill.
3. Replace the coolant reservoir cap. Turn
it clockwise until you feel a strong
resistance.
249
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
WARNING: When lifting a
plastic-cased battery, excessive pressure
on the end walls could cause acid to flow
through the vent caps, resulting in
personal injury and damage to the
vehicle or battery. Lift the battery with a
battery carrier or with your hands on
opposite corners.
WARNING: Keep batteries out of
reach of children. Batteries contain
sulfuric acid. Avoid contact with skin,
eyes or clothing. Shield your eyes when
working near the battery to protect
against possible splashing of acid
solution. In case of acid contact with skin
or eyes, flush immediately with water for
a minimum of 15 minutes and get prompt
medical attention. If acid is swallowed,
call a physician immediately.
E170684
To avoid fluid contamination, the reservoir
cap must remain in place and fully tight,
unless you are adding fluid.
Only use fluid that meets Ford
specifications. See Capacities and
Specifications (page 297).
WARNING: Battery posts,
terminals and related accessories
contain lead and lead compounds. Wash
hands after handling.
WARNING: For vehicles with
Auto-Start-Stop the battery requirement
is different. You must replace the battery
with one of exactly the same
specification.
CLUTCH FLUID CHECK
The clutch and brake systems share the
same fluid reservoir. See Brake Fluid
Check (page 249).
The battery is in the engine compartment.
See Under Hood Overview (page 238).
Your vehicle has a maintenance-free
If the vehicle battery has a cover, make
sure you correctly install it after cleaning
or replacing the battery.
WARNING: Batteries normally
produce explosive gases which can
cause personal injury. Therefore, do not
allow flames, sparks or lighted
substances to come near the battery.
When working near the battery, always
shield your face and protect your eyes.
Always provide correct ventilation.
250
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
For longer, trouble-free operation, keep the
Remove and Reinstall the Battery
top of the battery clean and dry and the
battery cables tightly fastened to the
battery terminals. If any corrosion is
present on the battery or terminals, remove
the cables from the terminals and clean
with a wire brush. You can neutralize the
acid with a solution of baking soda and
water.
To disconnect or remove the battery, do
the following:
1. Apply the parking brake and switch the
ignition off.
2. Switch all electrical equipment off, for
example lights and radio.
3. Wait a minimum of two minutes before
disconnecting the battery.
We recommend that you disconnect the
negative battery cable terminal from the
battery if you plan to store your vehicle for
an extended period.
Note: If you only disconnect the negative
battery cable terminal, make sure it is
isolated or placed away from the battery
terminal to avoid unintended connection or
arcing.
Note: The engine management system has
a power hold function and remains powered
for a period of time after you switch the
ignition off. This is to allow diagnostic and
adaptive tables to be stored. Disconnecting
the battery without waiting can cause
damage not covered by the vehicle
Warranty.
To maintain correct operation of the
battery management system, if you add
any electrical devices to your vehicle, do
not connect the ground connection directly
to the negative battery terminal. A
connection at the negative battery terminal
can cause inaccurate measurements of
the battery condition and potential
incorrect system operation.
Note: If you add electrical accessories or
components to your vehicle this may
adversely affect battery performance,
durability and the performance of other
electrical systems on your vehicle.
4. Disconnect the negative battery cable
terminal.
5. Disconnect the positive battery cable
terminal.
6. Remove the battery securing clamp.
7. Remove the battery.
8. To install, reverse the removal
procedure.
Note: Before reconnecting the battery,
make sure the ignition remains switched off.
Note: Make sure the battery cable terminals
are fully tightened.
If you replace the battery make sure it
matches the electrical requirements of
your vehicle.
If you disconnect or replace the vehicle
battery, you must reset the following
features:
If you disconnect or replace the battery
and your vehicle has an automatic
transmission, it must relearn its adaptive
strategy. Because of this, the transmission
may shift firmly when first driven. This is
normal operation while the transmission
fully updates its operation to optimum
shift feel.
•
Window bounce-back. See Opening
and Closing the Windows (page 79).
•
•
Clock Settings.
Pre-set radio stations.
251
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Battery Disposal
CHANGINGTHEFRONTWIPER
BLADES
Make sure that you dispose of
old batteries in an
environmentally friendly way.
Seek advice from your local authority
about recycling old batteries.
2
WASHER FLUID CHECK
When adding fluid, use a mixture of washer
fluid and water to help prevent freezing
and improve the cleaning capability. For
information on fluid dilution follow the
manufacturer's instructions.
1
E72899
1. Lift the wiper arm and then press the
wiper blade locking button.
Note: The reservoir supplies the front and
Note: Do not hold the wiper blade to lift the
rear washer systems.
wiper arm.
2. Remove the wiper blade.
CHECKING THE WIPER
BLADES
Note: Make sure that the wiper arm does
not spring back against the glass when the
wiper blade is not attached.
3. To install, reverse the removal
procedure.
Note: Make sure that the wiper blade locks
into place.
CHANGING THE REAR WIPER
BLADES
E142463
1. Lift the wiper arm.
Run the tip of your fingers over the edge of
the blade to check for roughness.
Clean the wiper blades with washer fluid
or water applied with a soft sponge or
cloth.
Note: Do not hold the wiper blade to lift the
wiper arm.
252
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
2
3
2
1
E183236
E236623
2. Disengage the wiper blade from the
wiper arm.
Note: Make sure that the wiper arm does
not spring back against the glass when the
wiper blade is not attached.
1. Use a suitable tool, for example a
screwdriver, to carefully remove the
trim clip.
Note: Raise the center pin and then remove
the clip.
3. To install, reverse the removal
2. Remove the screws.
procedure.
Note: Make sure that the wiper blade locks
into place.
REMOVING A HEADLAMP
WARNING: Switch the lamps and
the ignition off. Failure to do so could
result in serious personal injury.
E249609
3. Place your hand below the headlamp
housing and lift the headlamp at the
center area to disengage the lower
fixing clip.
4. Carefully lift the headlamp up at the
front and rear to disengage it from the
fixing points.
253
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Note: Take care when removing the
headlamp. There are rupture points adjacent
to the securing screws that are designed to
separate under impact.
5. Slightly rotate the rear of the headlamp
toward the center of the vehicle so that
it clears the front fender.
1
6. Move the headlamp slightly backwards
to clear the radiator grille panel. Then
lift the headlamp straight upward.
7. Disconnect the electrical connector.
8. Remove the headlamp.
2
9. To install, reverse the removal
E237938
procedure.
1. Carefully cut the trim to access the
lamp release wing nut.
REMOVING A REAR LAMP
2. Turn the wing nut counterclockwise to
Brake Lamp, Rear Lamp and
release the lamp.
Direction Indicator
Note: You cannot fully remove the wing
nut.
E237937
E236624
3. Remove the lamp.
4. Disconnect the electrical connector.
5. To install, reverse the removal
procedure.
254
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Reversing Lamp
CHANGING A BULB
WARNING: Switch the lamps and
the ignition off. Failure to do so could
result in serious personal injury.
WARNING: Lamps and associated
components become hot when in use.
Let them cool down before you remove
them.
3
Use the correct specification bulb. See
Bulb Specification Chart (page 311).
Headlamp
E236638
You may have to remove the headlamp
assembly prior to replacing a bulb. See
Removing a Headlamp (page 253).
1. Open the liftgate.
2. Carefully remove the cover.
3. Turn the wing nut counterclockwise
and remove it.
A
E249611
A
Daytime running lamp.
E238054
4. Remove the lamp.
5. Disconnect the electrical connector.
6. To install, reverse the removal
procedure.
255
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
A
B
C
E236599
E249637
3. Turn the bulb holder counterclockwise
A
B
Front direction indicator.
and remove it.
High beam headlamp and
Note: You cannot separate the bulb from
daytime running lamp.
the bulb holder.
C
Low beam headlamp.
4. To install, reverse the removal
procedure.
Low Beam Headlamp
1. Carefully remove the cover.
Note: Do not touch the bulb glass.
Projector Headlamp
A
E249634
E249612
2. Press the clip up to release the bulb
holder.
A
Daytime running lamp.
3. Remove the bulb holder by pulling it
straight out.
A
B
C
4. Remove the bulb by pulling it straight
out.
5. To install, reverse the removal
procedure.
Note: Do not touch the bulb glass.
E236599
High Beam Headlamp and Daytime
Running Lamp
A
B
C
Front direction indicator.
High beam headlamp.
Low beam headlamp.
1. Carefully remove the cover.
2. Disconnect the electrical connector.
256
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Low Beam Headlamp
Daytime Running Lamp
1. Carefully remove the cover.
These lamps have LEDs.
2. Disconnect the electrical connector.
Note: We recommend that you have LEDs
changed by an authorized dealer.
Front Direction Indicator
E249647
3. Turn the bulb holder counterclockwise
and remove it.
E236630
4. Remove the bulb.
1. Turn the bulb holder counterclockwise
and remove it.
5. To install, reverse the removal
procedure.
2. Press the bulb in and turn the bulb
Note: Do not touch the bulb glass.
counterclockwise to remove it.
High Beam Headlamp
1. Carefully remove the cover.
3. To install, reverse the removal
procedure.
LED Headlamp
A
E249660
E272995
2. Press the clip up to release the bulb
holder.
A
Daytime running lamp.
3. Remove the bulb holder by pulling it
straight out.
These lamps have LEDs.
4. Remove the bulb by pulling it straight
out.
Note: We recommend that you have LEDs
changed by an authorized dealer.
5. To install, reverse the removal
procedure.
Note: Do not touch the bulb glass.
257
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Note: Do not touch the bulb glass.
Front Fog Lamp
ST, ST Line and Vignale
All Vehicles - Excluding: ST, ST Line
and Vignale
E159695
1. Use a suitable tool, for example a
screwdriver, to carefully remove the
wheel arch liner fasteners. Pull the
wheel liner back toward the tire to gain
access to the bulb.
E273066
1. Use a suitable tool, for example a
screwdriver, to carefully remove the
housing cover.
2. Disconnect the electrical connector.
2
2
2
E273068
2. Remove the screws and the lamp.
3. Disconnect the electrical connector.
4. Turn the bulb holder counterclockwise
and remove it.
Note: You cannot separate the bulb from
E236628
the bulb holder.
5. To install, reverse the removal
3. Turn the bulb holder counterclockwise
and remove it.
procedure.
Note: You cannot separate the bulb from
the bulb holder.
4. To install, reverse the removal
procedure.
258
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
Side Direction Indicator
E283366
4. Use a suitable tool, for example a
E283364
screwdriver, to push the housing cover
through the access hole and remove it.
1. Use a suitable tool, for example a
screwdriver, to carefully lever the mirror
glass from the lower outer edge and
remove it.
2. Unplug the connector from the rear
side of the glass.
E283367
5. Use a T10 Torx screwdriver to remove
the lamp body.
E283365
3. Use a suitable tool, for example a
screwdriver, to carefully press the two
housing cover clips and release them.
259
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
2. Press the bulb in and turn the bulb
counterclockwise to remove it.
3. To install, reverse the removal
procedure.
Note: High series have LEDs.
Note: We recommend that you have LEDs
changed by an authorized dealer.
Rear Direction Indicator
E283430
2
1
6. Turn the bulb holder clockwise and
remove it.
7. Pull the bulb straight out.
8. To install, reverse the removal
procedure.
Note: Make sure that both mirror housing
cover clips lock into position.
Note: We recommend that you have bulbs
E236635
changed by an authorized dealer.
1. Turn the bulb holder counterclockwise
and remove it.
Rear Lamp
Remove the rear lamp assembly prior to
replacing any bulb. See Removing a Rear
Lamp (page 254).
2. Press the bulb in and turn the bulb
counterclockwise to remove it.
3. To install, reverse the removal
procedure.
Reversing Lamp
2
1
2
E236636
1. Turn the bulb holder counterclockwise
and remove it.
E236634
1. Turn the bulb holder counterclockwise
and remove it.
2. Press the bulb in and turn the bulb
counterclockwise to remove it.
260
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Maintenance
3. To install, reverse the removal
procedure.
License Plate Lamp
These lamps have LEDs.
Note: We recommend that you have LEDs
changed by an authorized dealer.
High Mounted Stoplamp
These lamps have LEDs.
Note: We recommend that you have LEDs
changed by an authorized dealer.
Rear Fog Lamp
Access the underside of your vehicle
behind the rear wheel.
2
E236637
1. Turn the bulb holder counterclockwise
and remove it.
2. Press the bulb in and turn the bulb
counterclockwise to remove it.
3. To install, reverse the removal
procedure.
261
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
