Deutsch
EnglishWheels and Tires -> Changing a Road Wheel-Vehicles With-Spare Wheel for your Ford Fiesta 2017-2023
Wheels and Tires
How Temperature Affects Your Tire
If the tires are rotated, you need to reset
the system in order to relearn the positions
of the tire pressure sensors. The system
cannot tell which position a tire pressure
sensor is in, and assumes you have set the
tire pressures correctly.
Pressure
The tire pressure monitoring system
monitors tire pressure in each pneumatic
tire. While driving in a normal manner, a
typical passenger tire inflation pressure
may increase about 14–28 kPa (2–4 psi)
from a cold start situation. If the vehicle is
stationary overnight with the outside
temperature significantly lower than the
daytime temperature, the tire pressure may
decrease about 21 kPa (3 psi) for a drop of
30°F (17°C) in ambient temperature. This
lower pressure value may be detected by
the tire pressure monitoring system as
being significantly lower than the
Performing the Reset Procedure
1. Switch the ignition on.
2. Navigate to the tire monitor menu in
the information display. See
Information Messages (page 95).
3. Press and hold the OK button until a
confirmation message appears. If your
vehicle has a tire pressure monitoring
system reset button, press and hold
the button until a confirmation
message appears.
recommended inflation pressure and
activate the system warning light for low
tire pressure. If the low tire pressure
warning light is on, visually check each tire
to verify that no tire is flat. If one or more
tires are flat, repair as necessary. Check
the air pressure in the road tires. If any tire
is under-inflated, carefully drive the vehicle
to the nearest location where air can be
added to the tires. Inflate all the tires to
the recommended inflation pressure.
CHANGING A ROAD WHEEL -
VEHICLES WITH: SPARE
WHEEL
Vehicles With a Spare Wheel
Tire Pressure Monitoring System
WARNING: Do not fit more than
one spare wheel on your vehicle at any
one time.
Reset Procedure
Overview
You must carry out the system reset
procedure after each tire replacement or
adjustment of the tire pressures.
To maintain your vehicle load carrying
capability, your vehicle may require
different tire pressures in the front
compared to the rear. In these cases, the
system illuminates the warning lamp at
different pressures for the front and rear
tires.
WARNING: Do not carry out any
tire repairs on a spare wheel.
WARNING:If you are not sure what
type of spare wheel your vehicle has, do
not exceed 80 km/h (50 mph).
WARNING: Only fit snow chains to
specified tires.
If the spare wheel is the same type and
size as your vehicle road wheel, you can fit
the spare wheel and continue to drive in
the normal manner.
278
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
If the spare wheel is not the same type and
1. Turn the spare wheel securing nut
counterclockwise and remove it.
Remove the wheel from the spare
wheel well.
size as your vehicle road wheel, it has a
label showing the maximum driving speed
limit.
Refer to the following information before
changing the road wheel.
Note: Your vehicle may exhibit some
different driving characteristics if you fit the
spare wheel.
Note: The ground clearance of your vehicle
may be reduced when the spare wheel is
fitted. Take care when parking next to a
curb.
2
Note: The spare wheel is located under the
floor cover in the luggage compartment.
Note: If the spare wheel is fitted to your
vehicle, do not drive through an automatic
car wash.
Note: If the spare wheel is fitted to your
vehicle, drive the shortest distance possible.
1
3
E178548
2. Turn the vehicle jack securing bolt
counterclockwise and remove it.
3. Turn the vehicle jack screw clockwise
to remove the vehicle jack handle and
lug nut tool from the vehicle jack.
E178549
279
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
WARNING: Never place anything
between the vehicle jack and the ground.
WARNING: Never place anything
between the vehicle jack and your
vehicle.
WARNING: Use a jack with a
minimum lifting capacity of 1,500 kg
(3,307 lb) and a lifting plate with a
minimum diameter of 80 mm (3.1 in).
WARNING: Do not work on your
vehicle when the jack is the only support.
If the vehicle slips off the jack, you or
someone else could be seriously injured.
E245204
4. Unfold the vehicle jack handle and the
hexagonal end into the correct position
prior to use. Use the hexagonal end to
operate the vehicle jack screw and to
remove the lug nuts.
WARNING:No person should place
any portion of their body under a vehicle
that is supported by a jack.
Note: Use the hook at the hexagonal end
WARNING: Do not get under a
vehicle that is only supported by a
vehicle jack.
to remove the wheel trim.
Vehicles Without a Spare Wheel
Vehicles without a spare wheel are fitted
with a temporary mobility kit. See Tire
Sealant and Inflator Kit (page 268).
Note: Vehicles with a temporary mobility
kit do not have a spare wheel, vehicle jack
or wheel brace.
Vehicle Jack
E166722
WARNING: The jack supplied with
this vehicle is only intended for changing
wheels. Do not use the vehicle jack other
than when you are changing a wheel in
an emergency.
Workshop Type Hydraulic Trolley Jack
WARNING: Use a jack with a
minimum lifting capacity of 1,500 kg
(3,307 lb) and a lifting plate with a
minimum diameter of 80 mm (3.1 in).
WARNING: Check that the vehicle
jack is not damaged or deformed and
the thread is lubricated and clean.
We recommend you use a workshop type
hydraulic trolley jack for changing between
summer and winter tires.
280
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
Refer to vehicle jack manufacturer's
instructions.
Jacking and Lifting Points
WARNING: You must use the
specified jacking points.
E93020
A
B
E283868
A
B
Emergency use only.
Maintenance.
281
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
A
E93184
Indentations in the sills show the location
of the jacking points.
All Vehicles - Excluding: Active, ST and
ST Line
E93020
Active, ST and ST Line
E283869
E92932
282
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
Removing the Wheel Trim
WARNING: If your vehicle has a
manual transmission, shift into first or
reverse gear. If your vehicle has an
automatic transmission, shift into park
(P).
WARNING: Make sure all
passengers are out of your vehicle.
WARNING: Chock the diagonally
opposite wheel to the punctured tire with
an appropriate wheel block or wheel
chock.
WARNING: Do not work on your
vehicle when the jack is the only support.
If the vehicle slips off the jack, you or
someone else could be seriously injured.
E285279
1. Unfold the lug nut wrench.
2. Use the tongue on the lug nut wrench
to remove the wheel trim.
Removing a Road Wheel
E166722
WARNING: Park your vehicle in
such a position that neither the traffic
nor you are hindered or endangered.
WARNING: Make sure that the
vehicle jack is vertical to the jacking point
and the base is flat on the ground.
WARNING: Park your vehicle so
that you do not obstruct the flow of
traffic or place yourself in any danger and
set up a warning triangle.
1. Install the locking lug nut key.
WARNING: Make sure that your
vehicle is on firm and level ground with
the front wheels pointing straight ahead.
WARNING: Switch the ignition off
and apply the parking brake.
283
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
correct metal-to-metal contact at the
wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to
come off while your vehicle is in motion,
resulting in loss of vehicle control,
personal injury or death.
1
WARNING: Make sure that the
arrows on directional tires point in the
direction of rotation when your vehicle
is moving forward. If you have to fit a
spare tire with the arrows pointing in the
opposite direction have the tire refitted
as soon as possible.
2
WARNING: Use only approved
wheel and tire sizes. Using other sizes
could damage your vehicle and will make
the National Type Approval invalid.
WARNING: Make sure there is no
grease or oil on the threads or the
surface between the wheel lugs and
nuts. This can cause the lug nuts to
loosen while driving.
E181745
2. Loosen the lug nuts.
3. Raise your vehicle until the tire is clear
of the ground.
WARNING: Do not fit run flat tires
on vehicles that were not originally fitted
with them. Contact an authorized dealer
for more details about compatibility.
4. Remove the lug nuts and the road
wheel.
Note: Do not lay alloy wheels face down
on the ground. This may damage the paint.
Installing a Road Wheel
WARNING: Do not install alloy
wheels using lug nuts designed for use
with steel wheels.
WARNING: When you install a
wheel, always remove any corrosion, dirt
or foreign materials present on the
mounting surfaces of the wheel or the
surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Make
sure to secure any fasteners that attach
the rotor to the hub so they do not
WARNING: Have the lug nuts
checked for tightness and the tire
pressure checked as soon as possible.
WARNING: Only use the specific
lug nuts and wheels supplied with your
vehicle. If in doubt, contact an authorized
dealer.
interfere with the mounting surfaces of
the wheel. Installing wheels without
284
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Wheels and Tires
Note: The lug nuts of alloy wheels and
TIRE PRESSURES - 1.0L
ECOBOOST™, MANUAL
TRANSMISSION
The recommended tire inflation pressures
are on the tire information label on the
driver side B-pillar.
spoked steel wheels can also be used for
the steel spare wheel for a short time
(maximum two weeks).
Note: Make sure that the cones on the lug
nuts are against the wheel.
1. Install the wheel.
2. Install the lug nuts finger tight.
3. Install the locking lug nut key.
Check all tire pressures when they are cold,
at least once every two weeks.
Note: You may need to remove the spare
wheel from the spare wheel well to check
the tire pressure.
3
A
B
C
D
E
1
2
x x x x x x
x x x x x x x x
x x x x x x
x x x x x x
x x x x x x x x
x x
4
F
I
H
G
E90589
E254054
4. Install all of the lug nuts and partially
tighten them in the sequence shown.
5. Lower your vehicle and remove the
A
B
C
D
E
F
Tire size.
Vehicle model.
Front tire pressure.
Rear tire pressure.
Vehicle load.
vehicle jack.
6. Fully tighten all of the lug nuts in the
sequence shown. See Wheels and
Tires (page 268).
7. Install the wheel trim.
Measure unit.
G
H
I
Spare wheel tire pressure.
Intended constant vehicle speed.
Spare wheel tire size.
285
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
