Deutsch
EnglishMaintenance -> Wiper Blades for your Honda CR-V 2006-2010
09/07/16 18:49:21 31SWA630_372
Wiper Blades
Check the condition of the wiper
blades at least every six months.
Replace them if you find signs of
When replacing a wiper blade,
make sure not to drop the wiper
blade or wiper arm down on the
windshield.
Do not open the hood when the wiper
cracking in the rubber, areas that are arms are raised, or you will damage
getting hard, or if they leave streaks
and unwiped areas when used.
the hood and the wiper arms.
BLADE
FRONT
WIPER ARMS
LOCK TAB
3. Remove the blade from its holder
by grasping the tabbed end of the
blade. Pull firmly until the tabs
come out of the holder.
2. Disconnect the blade assembly
from the wiper arm:
To replace a front wiper blade:
1. Raise each wiper arm off the
windshield, lifting the driver’s side
first, then the passenger’s side.
Press and hold the lock tab.
Slide the blade assembly toward
the lock tab until it releases from
the wiper arm.
CONTINUED
367
09/07/16 18:49:31 31SWA630_373
Wiper Blades
4. Examine the new wiper blades. If
they have no plastic or metal
reinforcement along the back
edge, remove the metal
reinforcement strips from the old
wiper blade, and install them in
the slots along the edge of the new
blade.
6. Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
7. Lower the wiper arm down against
the windshield, the passenger’s
side first, then the driver’s side.
REINFORCEMENT
BLADE
TOP
5. Place the top of the wiper blade on
the end of the blade assembly, and
slide the blade onto the assembly
in the direction pointed to by the
arrow.
Make sure the blade is completely
installed.
Make sure the three rubber tabs
inside the blade fit to each notch
of the reinforcement, as shown.
368
09/07/16 18:49:45 31SWA630_374
Wiper Blades
5. Slide the new blade into the holder.
Make sure it is engaged in the slot
along its full length.
Insert both ends of the blade into
the holder. Make sure they are
secure.
REAR
6. Install the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
7. Lower the wiper arm against the
windshield.
To replace a rear wiper blade:
3. Pull one end of the blade out from
the holder.
Slide the blade out of the holder.
1. Raise the wiper arm off the rear
window.
4. Examine the new wiper blades. If
they have no plastic or metal
reinforcement along the back
edge, remove the metal
2. Disconnect the blade assembly
from the wiper arm by pivoting the
blade assembly upward.
reinforcement strips from the old
wiper blade, and install them in
the slots along the edge of the new
blade.
369
09/07/16 18:49:55 31SWA630_375
Tires
To safely operate your vehicle, your
tires must be the proper type and
size, in good condition with adequate
tread, and correctly inflated.
Inflation Guidelines
The tire pressure monitoring system
(TPMS) warns you when a tire
pressure is low. See page 326 for
more information.
Keeping the tires properly inflated
provides the best combination of
handling, tread life, and riding
comfort.
The following pages give more
detailed information on how to take
care of your tires and what to do
when they need to be replaced.
Even though your vehicle is
equipped with TPMS, we
Underinflated tires wear unevenly,
adversely affect handling and fuel
economy, and are more likely to
fail from being overheated.
recommend that you visually check
your tires every day. If you think a
tire might be low, check it
immediately with a tire gauge.
Overinflated tires can make your
vehicle ride more harshly, are
more prone to damage from road
hazards, and wear unevenly.
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.
370
