Deutsch
EnglishDriving for your Honda CR-V 2011-2015
Towing a Trailer
Towing Preparation
1Towing Load Limits
Towing Load Limits
■
Your vehicle can tow a trailer if you carefully observe the load limits, use the proper
equipment, and follow the towing guidelines. Check the load limits before driving.
3
WARNING
Exceeding any load limit or improperly
loading your vehicle and trailer can cause a
crash in which you can be seriously hurt or
killed.
■
Total trailer weight
Maximum allowable weight of the trailer,
cargo, and everything in or on it must not
exceed 1,500 lbs (680 kg). Towing loads in
excess of this can seriously affect vehicle
handling and performance and can damage
the engine and drivetrain.
Check the loading of your vehicle and
trailer carefully before starting to drive.
Check if all loads are within limits at a public scale.
If a public scale is not available, add the estimated
weight of your cargo load to the weight of your
trailer (as quoted by the manufacturer), and the
tongue load.
Total Load
■
Tongue load
The weight of the tongue with a fully loaded
trailer on the hitch should be approximately
10% of the total trailer weight.
• Excessive tongue load reduces front tire
traction and steering control. Too little
tongue load can make the trailer unstable
and cause it to sway.
• To achieve a proper tongue load, start by
loading 60% of the load toward the front
of the trailer and 40% toward the rear.
Readjust the load as needed.
Break-in Period
Avoid towing a trailer during your vehicle's first 600
miles (1,000 km).
Never exceed the gross weight ratings.
Gross weight information
2 Vehicle Specifications P. 510
Tongue Load
T
Continued
353
uuTowing a TraileruTowing Preparation
1Towing Equipment and Accessories
Towing Equipment and Accessories
■
Make sure that all equipment is properly installed and
maintained, and that it meets federal, state, province/
territory, and local regulations.
Towing equipment varies by the size of your trailer, how much load you are towing,
and where you are towing.
Consult your trailer sales or rental agency if any other
items are recommended or required for your towing
situation.
■
Hitches
The hitch must be of an approved type and properly bolted to the underbody.
■
Safety chains
The lighting and wiring of trailers can vary by type
and brand. If a connector is required, it should only
be installed by a qualified technician.
Always use safety chains when you tow a trailer. Leave enough slack to allow the
trailer to turn corners easily, but do not allow the chains to drag on the ground.
■
Trailer brakes
Recommended for any trailer with a total weight of 1,000 lbs (450 kg) or more:
There are two common types of trailer brakes: surge and electric. Surge brakes are
common for boat trailers, since the brakes will get wet. If you choose electric brakes,
be sure they are electronically actuated. Do not attempt to attach trailer brakes to
your vehicle's hydraulic system, as it will lower braking effectiveness and create a
potential hazard.
■
Additional towing equipment
Many states and provinces/territories require special outside mirrors when towing a
trailer. Even if mirrors are not required in your locale, you should install special
mirrors if visibility is restricted in any way.
354
uuTowing a TraileruTowing Preparation
■
Trailer light
Trailer lights and equipment must comply with federal, state, province/territory, and
local regulations. Check with your local trailer sales or rental agency for the
requirements in the area where you plan to tow.
Backup Light (Brown)
Brake Light (Pink)
Option (Yellow)
Small (Red)
Left Turn Signal (Violet)
Right Turn Signal (Green)
Grand (Black)
Your trailer lighting connector is located behind the left side panel in the cargo area.
Each pin’s purpose and wiring color code are shown in the image.
When using a non-Honda trailer lighting harness and converter, get the connector
and pins for your vehicle from a dealer.
355
uuTowing a TraileruDriving Safely with a Trailer
Driving Safely with a Trailer
1Driving Safely with a Trailer
Things You Need To Know Before Towing a Trailer
■
Operating speed when towing a trailer is restricted
up to 65 mph (100 km/h).
• Have the trailer properly serviced and keep it in good condition.
• Make sure that all the weights and load in the vehicle and trailer are within limits.
2 Towing Load Limits P. 353
Parking
In addition to the normal precautions, place wheel
chocks at each of the trailer's tires.
• Securely attach the hitch, safety chains, and other necessary parts to the trailer.
• Securely store all the items in and on the trailer so that they do not shift while
driving.
• Check if the lights and brakes on the trailer are working properly.
• Check the pressures of the trailer tires, including the spare.
Towing Speeds and Gears
■
• Drive slower than normal.
• Obey posted speed limits for vehicles with trailers.
• Use the (D position when towing a trailer on level roads.
Turning and Braking
■
• Turn more slowly and with a wider turning arc than normal.
• Allow more time and distance for braking.
• Do not brake or turn suddenly.
Driving in Hilly Terrain
■
• Monitor your temperature gauge. If it nears the red (Hot) mark, turn off the
heating and cooling system*/climate control system* and reduce speed. Pull to the
side of the road safely to cool down the engine if necessary.
* Not available on all models
356
uuTowing a TraileruTowing Your Vehicle
Towing Your Vehicle
Your vehicle is not designed to be towed behind a motor home. If your vehicle needs
to be towed in an emergency, refer to the emergency towing information.
2 Emergency Towing P. 506
357
Off-Highway Driving Guidelines
General Information
Your vehicle has been designed primarily for use on pavement, however, its higher
ground clearance allows you to occasionally travel on unpaved roads. It is not
designed for trail-blazing, or other challenging off-road activities.
1Off-Highway Driving Guidelines
3
WARNING
Improperly operating this vehicle on or off
pavement can cause a crash or rollover in
which you and your passengers can be
seriously injured or killed.
If you decide to drive on unpaved roads, you will find that it requires somewhat
different driving skills and that your vehicle will handle somewhat differently than it
does on pavement. Pay attention to the precautions and tips in this section, and get
acquainted with your vehicle before leaving the pavement.
• Follow all instructions and guidelines in
this owner’s manual.
• Keep your speed low, and don’t drive
Important Safety Precautions
To avoid loss of control or rollover, be sure to follow all precautions and
recommendations:
• Be sure to store cargo properly and do not exceed your cargo load limits.
2 Maximum Load Limit P. 351
Failure to operate your vehicle correctly might result
in a crash or a rollover.
2 Important Handling Information P. 30
2 Precautions While Driving P. 366
• Whenever you drive, make sure you and your passengers always wear seat belts.
• Keep your speed low, and never go faster than the conditions allow.
• It’s up to you to continually assess the situation and drive within the limits.
358
uuOff-Highway Driving GuidelinesuAvoiding Trouble
Avoiding Trouble
• Check Out Your Vehicle before you leave the pavement and make sure that all
scheduled maintenance has been completed. Pay special attention to the
condition of the tires, and check the tire pressures.
• Remember the route you choose presents limits (too steep or bumpy), you have
limits (driving skill and comfort), and your vehicle has limits (traction, stability, and
power). Failing to recognize these limits will likely put you and your passengers in
a hazardous situation.
• Accelerating and Braking should be done slowly and gradually. Trying to start
or stop too fast can cause a loss of traction and you could lose control.
• Avoiding Obstacles and Debris in the road reduces the likelihood of a rollover
or damage to your suspension or other components.
• Driving on Slopes increases your risk of a rollover, particularly if you attempt to
drive across a slope that is too steep. Going straight or down a slope is usually the
safest. If you can’t clearly see all conditions or obstacles on a slope, walk it before
you drive it. If there is any doubt whether you can safely pass, don’t try it. Find
another route. If you get stuck when climbing, do not try to turn around. Back
down slowly following the same route you took up the hill.
• Crossing a Stream - Avoid driving through deep water. If you encounter water
in your route (a small stream or large puddle, for example), evaluate it carefully
before going ahead. Make sure it is shallow, flowing slowly, and has firm ground
underneath. If you are not sure of the depth or the ground, turn around and find
another route. Driving through deep water can also damage your vehicle. The
water can get into the transmission and differential, diluting the lubricant and
causing an eventual failure. It can also wash the grease out of the wheel bearings.
• If You Get Stuck, carefully go in the direction that you think will get you
unstuck. Do not spin the tires as this will only make things worse and could
damage the transmission. If you are unable to free yourself, your vehicle will need
to be towed. Front and rear tow hooks are provided for this purpose.
359
When Driving
Models without smart entry system
Starting the Engine
1Starting the Engine
1. Make sure the parking brake is applied.
Keep your foot firmly on the brake pedal when
starting the engine.
The engine is harder to start in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
meters).
When starting the engine in cold weather, turn off all
electrical accessories such as the lights, heating and
cooling system*/climate control system*, and rear
defogger in order to reduce battery drain.
2. Check that the shift lever is in (P, then
depress the brake pedal.
u Although it is possible to start the vehicle
Brake Pedal
If you live in a region where winter is extremely cold,
an engine block heater will improve starting and
warming of the engine. If temperatures consistently
below −22°F (−30°C) are expected, the coolant
mixture should be changed to a higher concentration
to prevent freezing. Consult a dealer for details.
in (N, it is safer to start it in (P
.
If the exhaust system sounds abnormal or you can
smell exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
3. Turn the ignition switch to START (e
without depressing the accelerator pedal.
* Not available on all models
360
uuWhen DrivinguStarting the Engine
1Starting the Engine
Starting to Drive
■
Do not hold the key in START (e for more than 15
seconds.
1. Keeping your right foot on the brake pedal, release the parking brake. Check that
the parking brake indicator has gone off.
•
If the engine does not start right away, wait for at
least 10 seconds before trying again.
If the engine starts, but then immediately stops,
wait at least 10 seconds before repeating step 3
while gently depressing the accelerator pedal.
Release the accelerator pedal once the engine
starts.
2 Parking Brake P. 405
•
2. Put the shift lever in (D. Select (R when reversing.
3. Gradually release the brake pedal and gently depress the accelerator pedal to pull
away.
■
Hill start assist system
Hill start assist keeps the brake engaged briefly to help prevent the vehicle from
rolling on inclines as you move your foot from the brake pedal to the accelerator.
theft. If an improperly coded key (or other device) is
used, the engine's fuel system is disabled.
2 Immobilizer System P. 147
Move the shift lever to (D or (S when facing uphill, or (R when facing downhill,
then release the brake pedal.
1Hill start assist system
Hill start assist may not prevent the vehicle from
rolling downhill on a very steep or slippery slope, and
does not operate on small inclines.
Hill start assist is not a replacement for the parking
brake.
Hill start assist will operate even when VSA® is
switched off.
361
uuWhen DrivinguStarting the Engine
Models with smart entry system
Starting the Engine
1Starting the Engine
1. Make sure the parking brake is applied.
Keep your foot firmly on the brake pedal when
starting the engine.
The engine is harder to start in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
meters).
When starting the engine in cold weather, turn off all
electrical accessories such as the lights, climate
control system, and rear defogger in order to reduce
battery drain.
2. Check that the shift lever is in (P, then
depress the brake pedal.
u Although it is possible to start the vehicle
If you live in a region where winter is extremely cold,
an engine block heater will improve starting and
warming of the engine. If temperatures consistently
below −22°F (−30°C) are expected, the coolant
mixture should be changed to a higher concentration
to prevent freezing. Consult a dealer for details.
in (N, it is safer to start it in (P
.
Brake Pedal
If the exhaust system sounds abnormal or you can
smell exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
The immobilizer system protects your vehicle from
theft.
If an improperly coded device is used, the engine’s
fuel system is disabled.
2 Immobilizer System P. 147
362
uuWhen DrivinguStarting the Engine
3. Press the ENGINE START/STOP button
1Starting the Engine
without depressing the accelerator pedal.
Bring the smart entry remote close to the ENGINE
START/STOP button if the battery in the smart entry
remote is weak.
2 If the Smart Entry Remote Battery is Weak
P. 492
The engine may not start if the smart entry remote is
subjected to strong radio waves.
Do not hold the ENGINE START/STOP button to
start the engine.
If the engine does not start, wait at least 10 seconds
before trying again.
Continued
363
uuWhen DrivinguStarting the Engine
Stopping the Engine
■
You can turn the engine off when the vehicle is completely stopped.
1. Shift to (P
.
Starting to Drive
■
1. Keeping your right foot on the brake pedal, release the parking brake. Check that
the parking brake indicator has gone off.
2 Parking Brake P. 405
2. Put the shift lever in (D. Select (R when reversing.
3. Gradually release the brake pedal and gently depress the accelerator pedal to pull
away.
364
uuWhen DrivinguStarting the Engine
■
Hill start assist system
1Hill start assist system
Hill start assist keeps the brake engaged briefly to help prevent the vehicle from
rolling on inclines as you move your foot from the brake pedal to the accelerator.
Hill start assist may not prevent the vehicle from
rolling downhill on a very steep or slippery slope, and
does not operate on small inclines.
Move the shift lever to (D
downhill, then release the brake pedal.
, (S, or (L when facing uphill, or (R when facing
Hill start assist is not a replacement for the parking
brake.
365
uuWhen DrivinguPrecautions While Driving
Precautions While Driving
1Precautions While Driving
Driving Guidelines for Your Utility Vehicle
■
NOTICE
Utility vehicles have a significantly higher rollover rate than other types of vehicles.
To prevent rollovers or loss of control:
Do not operate the shift lever while pressing the
accelerator pedal. You could damage the
transmission.
• Take corners at slower speeds than you would with a passenger vehicle.
• Avoid sharp turns and abrupt maneuvers whenever possible.
• Do not modify your vehicle in any way that you would raise the center of gravity.
• Never carry more than 165 lbs (75 kg) of cargo on the roof rack (Honda
accessory).
NOTICE
If you repeatedly turn the steering wheel at an
extremely low speed, or hold the steering wheel on
the full left or right position for a while, the system
heats up. The system goes into a protective mode,
and limits its performance. The steering wheel
becomes harder and harder to operate. Once the
system cools down, the EPS system is restored.
Repeated operation under these conditions can
eventually damage the system.
In Rain
■
Avoid driving in deep water and on flooded roads. This can damage the engine,
driveline, or cause electrical component failure.
Other Precautions
■
If there is a strong impact with something under the vehicle, stop in a safe location.
Check the underside of the vehicle for damage or any fluid leaks.
366
uuWhen DrivinguContinuously Variable Transmission
1Precautions While Driving
Continuously Variable Transmission
Creeping
■
If the ignition switch is turned to ACCESSORY (q or
LOCK (0*1 while driving, the engine will shut down
and all steering and brake power assist functions will
stop, making it difficult to control the vehicle.
The engine runs at a higher idle speed and creeping increases.
Keep the brake pedal firmly depressed when stopped.
Kickdown
■
Do not put the shift lever in (N, as you will lose
Quickly depressing the accelerator pedal while driving uphill may cause the
transmission to drop to a lower gear, unexpectedly increasing vehicle speed. Depress
the accelerator pedal carefully, especially on slippery roads and curves.
engine braking (and acceleration) performance.
During the first 600 miles (1,000 km) of operation,
avoid sudden acceleration or full throttle operation so
as to not damage the engine or powertrain.
Avoid hard braking for the first 200 miles (300 km).
You should also follow this when the brake pads are
replaced.
*1: Models with the smart entry system have an
ENGINE START/STOP button instead of an ignition
switch.
1Driving Guidelines for Your Utility Vehicle
Failure to operate your vehicle correctly might result
in a crash or a rollover.
2 Important Handling Information P. 30
2 Precautions While Driving P. 366
367
uuWhen DrivinguShifting
Shifting
Change the shift position in accordance with your driving needs.
1Shifting
■
Shift lever positions
You cannot turn the ignition switch to LOCK (0*1
and remove the key unless the shift lever is in (P
.
The vehicle may move forward very slightly even in
(N while the engine is cold.
Depress the brake pedal firmly and, when necessary,
apply the parking brake.
Park
Used when parking or starting the engine
Reverse
Used when reversing
*1: Models with the smart entry system have an
ENGINE START/STOP button instead of an ignition
switch.
Neutral
Used when idling
Drive
Used for normal driving
Drive (S)
Used:
●
For better acceleration
To increase engine braking
When going up or down hills
●
Release Button
●
Low
●
Used to further increase engine braking
Used when going up or down hills
●
368
uuWhen DrivinguShifting
1Shift Lever Operation
Shift Lever Operation
■
NOTICE
When you change the shift lever from (D to (R and
vice versa, come to a complete stop and keep the
brake pedal depressed.
Tachometer's red zone
Operating the shift lever before the vehicle has come
to a complete standstill can damage the transmission.
Shift Lever Position Indicator
Use the shift lever position indicator to check the
lever position before pulling away.
If the transmission indicator (D blinks when driving,
in any shift position, there is a problem with the
transmission.
Avoid sudden acceleration and have the transmission
checked by a dealer as soon as possible.
The fuel supply may be cut off if you drive at engine
speeds in or over the tachometer's red zone (engine
speed limit). If this happens, you may experience a
slight jolt.
Depress the brake pedal and press the
shift lever release button to shift.
Shift without pressing the shift lever
release button.
It may not be possible to operate the shift lever if the
brake pedal is applied while the shift lever release
button is held down.
Press the shift lever release button
and shift.
Depress the brake pedal first.
369
uuWhen DrivinguECON Button
ECON Button
The ECON button turns the ECON mode on
and off.
The ECON mode helps you improve your fuel
economy by adjusting the performance of the
engine, transmission, air conditioning system,
and cruise control.
370
uuWhen DrivinguCruise Control*
Cruise Control*
Maintains a constant vehicle speed without having to keep your foot on the
accelerator pedal. Use cruise control on freeways or open roads where you can
travel at a constant speed with little acceleration or deceleration.
1Cruise Control*
3
WARNING
Improper use of the cruise control can lead
to a crash.
When to use
■
Vehicle speed for cruise control:
Desired speed in a range above
roughly 25 mph (40 km/h) ~
Always keep sufficient distance
between you and the vehicle in
front of you.
Use the cruise control only when traveling
on open highways in good weather.
■
Shift positions for cruise control:
In (D or (S
It may not be possible to maintain a constant speed
when driving uphill or downhill.
When not using cruise control:
Turn off cruise control by pressing the CRUISE
button.
How to use
CRUISE MAIN is on in the
instrument panel.
Cruise control is ready to use.
While in the ECON mode, it may take relatively more
time to accelerate to maintain the set speed.
■
Press the CRUISE button on
the steering wheel.
* Not available on all models
Continued
371
uuWhen DrivinguCruise Control*
To Set the Vehicle Speed
■
−/SET Button
On
On
On when cruise control begins
Press and release
Take your foot off the pedal and press the −/SET button when you reach the desired
speed.
The moment you release the −/SET button, the set speed is fixed, and cruise control
begins. The CRUISE CONTROL indicator comes on.
372
uuWhen DrivinguCruise Control*
1To Adjust the Vehicle Speed
To Adjust the Vehicle Speed
■
You can set the vehicle speed using the −/SET button
on the steering wheel when adjusting the speed with
the accelerator and brake pedals.
Increase or decrease the vehicle speed using the RES/+ or −/SET buttons on the
steering wheel.
To increase speed
To decrease speed
• Each time you press the button, the vehicle speed is increased or decreased by
about 1 mph (1.6 km/h).
• If you keep the button pressed, the vehicle speed increases or decreases until you
release it. This speed is then set.
1To Cancel
Resuming the prior set speed:
To Cancel
■
After cruise control has been canceled, you can still
resume the prior set speed by pressing the RES/+
button while driving at a speed of at least 25 mph (40
km/h) or more.
To cancel cruise control, do any of the
following:
• Press the CANCEL button.
• Press the CRUISE button.
• Depress the brake pedal.
The CRUISE CONTROL indicator goes off.
CRUISE
Button
You cannot set or resume in the following situations:
•
•
When vehicle speed is less than 25 mph (40 km/h)
When the CRUISE button is turned off
CANCEL
Button
At vehicle speeds of 22 mph (35 km/h) or less, cruise
control is canceled automatically.
373
uuWhen DrivinguFront Sensor Camera*
Front Sensor Camera*
The camera, used in systems; such as LDW, LKAS, ACC and CMBSTM, is designed to
detect an object that triggers any of the systems to operate their functions.
1Front Sensor Camera*
Never apply a film or attach any objects to the
windshield that could obstruct the camera’s field of
vision.
Camera Location and Handling Tips
■
Scratches, nicks, and other damage to the windshield
within the camera’s field of vision can cause the
system to operate abnormally. If this occurs, we
recommend that you replace the windshield with a
genuine Honda replacement windshield. Making
even minor repairs within the camera’s field of vision
or installing an aftermarket replacement windshield
may also cause the system to operate abnormally.
After replacing the windshield, have a dealer
recalibrate the camera. Proper calibration of the
camera is necessary for the system to operate
properly.
This camera is located behind the rearview
mirror.
Front Sensor
Camera
To help reduce the likelihood that high interior
temperatures will cause the camera’s sensing
system to shut off, when parking, find a shady
area or face the front of the vehicle away from
the sun. If you use a reflective sun shade, do
not allow it to cover the camera housing.
Covering the camera can concentrate heat on
it.
Do not place an object on the top of the instrument
panel. It may reflect onto the windshield and prevent
the system from detecting lane lines properly.
If the SOME DRIVER ASSIST SYSTEMS CANNOT
OPERATE:
message appears:
•
Use the climate control system to cool down the
interior and, if necessary, also use defroster mode
with the air flow directed toward the camera.
Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the camera.
•
* Not available on all models
374
uuWhen DrivinguAdaptive Cruise Control (ACC)*
Adaptive Cruise Control (ACC)*
1Adaptive Cruise Control (ACC)*
Helps maintain a constant vehicle speed and a set following distance behind a
vehicle detected ahead of yours, without you having to keep your foot on the brake
or the accelerator.
3
WARNING
Improper use of ACC can lead to a crash.
When to use
Use ACC only when traveling on open
highways in good weather.
The camera is located
behind the rearview
mirror.
3
WARNING
ACC has limited braking capability.
When your vehicle speed drops below 22
mph, ACC will automatically cancel and no
longer will apply your vehicle's brakes.
Always be prepared to apply the brake
pedal when conditions require.
The radar sensor is inside
the front grille.
■
■
Vehicle speed for adaptive cruise control:
Desired speed in a range above roughly 25
mph (40 km/h) ~
Shift positions for adaptive cruise control:
In (D or (S
* Not available on all models
Continued
375
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1Adaptive Cruise Control (ACC)*
How to use
Important Reminder
ACC is on in the multi-
information display.
Adaptive cruise control is
ready to use.
As with any system, there are limits to ACC. Use the
brake pedal whenever necessary, and always keep a
safe distance between your vehicle and other
vehicles.
■
Press the MAIN button on
the steering wheel.
* Not available on all models
376
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1Adaptive Cruise Control (ACC)*
To Set the Vehicle Speed
■
–/SET Button
When not using adaptive cruise control: Turn off
adaptive cruise by pressing the MAIN button.
1To Set the Vehicle Speed
On when
adaptive cruise
control begins
You can switch the displayed set speed
measurements on the multi-information display
between mph and km/h.
Press and release
2 Customized Features P. 100, 114
Take your foot off the pedal and press the –/SET button when you reach the desired
speed.
The moment you release the –/SET button,
the set speed is fixed, and adaptive cruise
control begins.
Set Vehicle
Speed
Set Vehicle
Distance
u A vehicle icon and distance bars appear
on the multi-information display.
* Not available on all models
Continued
377
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1When in Operation
When in Operation
■
If the vehicle detected ahead of you slows down
abruptly, or if another vehicle is detected cutting in
front of you, the beeper sounds and a message
appears on the multi-information display to alert you
to brake.
■
There is a vehicle ahead
ACC monitors if a vehicle ahead of you enters the ACC range. If a vehicle is detected
doing so, the ACC system maintains or decelerates your vehicle’s set speed in order
to keep the vehicle’s set following-distance from the vehicle ahead.
2 To Change Vehicle Distance P. 382
Beep
■
When ACC detects a
vehicle within ACC range:
■
When the vehicle goes
out of ACC range:
The vehicle icon appears on the
multi-information display.
The vehicle icon on the
multi-information display
becomes a dotted-line
contour.
Depress the brake pedal, and keep an appropriate
distance from the vehicle ahead.
Even if the distance between your vehicle and the
vehicle detected ahead is short, ACC may start
accelerating your vehicle under the following
circumstances:
•
The vehicle detected ahead of you is going at
almost the same speed as, or faster than your
vehicle.
•
A vehicle that cuts in front of you is going faster
than your vehicle, gradually distancing itself from
you.
ACC Range: 394 ft. (120 m)
378
uuWhen DrivinguAdaptive Cruise Control (ACC)*
■
There is no vehicle ahead
1When in Operation
Your vehicle cruises at the set speed.
You can also set the system to beep when a vehicle
detected in front of you comes in and goes out of the
ACC detecting range. Change the ACC FORWARD
VEHICLE DETECT BEEP* setting.
■
A vehicle ahead is within ACC range and going slower than the set speed
Your vehicle slows down, and maintains the same speed as the speed of the vehicle
ahead to maintain the set following distance.
Limitations
■
A vehicle ahead is within ACC range and going at a steady speed
You may need to use the brake to maintain a safe
distance when using ACC. Additionally, ACC may
not work properly under certain conditions.
2 ACC Conditions and Limitations P. 380
Your vehicle follows the vehicle ahead of it, keeping a constant distance, without
going beyond the set speed.
■
A vehicle ahead goes out of range
ACC accelerates your vehicle to the set speed, and then maintains it.
■
When you depress the accelerator pedal
You can temporarily increase the vehicle speed. In this case, there is no audible or
visual alerts even if a vehicle is in ACC range.
ACC stays on unless you cancel it. Once you release the accelerator pedal, the
system resumes the set speed.
* Not available on all models
Continued
379
uuWhen DrivinguAdaptive Cruise Control (ACC)*
ACC Conditions and Limitations
■
The system may automatically shut off and the ACC indicator will come on under
certain conditions. Some examples of these conditions are listed below. Other
conditions may reduce some of the ACC functions.
2 Front Sensor Camera* P. 374
■
Environmental conditions
Driving in bad weather (rain, fog, snow, etc.).
■
Roadway conditions
Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks, reflected
lights, road spray, high contrast).
■
Vehicle conditions
• The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
• An abnormal tire or wheel condition (wrong sized, varied size or construction,
improperly inflated, compact spare tire, etc.).
• The camera temperature gets too hot.
• The parking brake is applied.
* Not available on all models
380
uuWhen DrivinguAdaptive Cruise Control (ACC)*
■
Detection limitations
• A vehicle or pedestrian suddenly crosses in front of you.
• The distance between your vehicle and the vehicle or pedestrian ahead of you is
too short.
• A vehicle or pedestrian cuts in front of you at a slow speed, and it brakes
suddenly.
• When you accelerate rapidly and approach the vehicle or pedestrian ahead of you
at high speed.
• The vehicle ahead of you is a motorcycle, bicycle, mobility scooter, or other small
vehicle.
• When there are animals in front of your vehicle.
• When you drive on a curved or winding or undulating road that makes it difficult
for the sensor to properly detect a vehicle or a pedestrian in front of you.
• The speed difference between your vehicle and a vehicle in front of you is
significantly large.
• An oncoming vehicle suddenly comes in front of you.
• Your vehicle abruptly crosses over in front of an oncoming vehicle.
• When driving through a narrow iron bridge.
Continued
381
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1To Adjust the Vehicle Speed
To Adjust the Vehicle Speed
■
If a vehicle detected ahead is going at a speed slower
than your increased set speed, ACC may not
accelerate your vehicle. This is to maintain the set
following distance between your vehicle and the
vehicle ahead.
Increase or decrease the vehicle speed using the RES/+ or –/SET buttons on the
steering wheel.
To increase speed
You can set the vehicle speed using the –/SET button
on the steering wheel when adjusting the speed with
the accelerator and brake pedals.
To decrease speed
• Each time you press the button, the vehicle speed is increased or decreased by
about 1 mph or 1 km/h accordingly.
• If you keep the button pressed, the vehicle speed increases or decreases by about
5 mph or 5 km/h accordingly.
To Change Vehicle Distance
■
Press the
range.
(distance) button to change ACC
Distance Button
Each time you press the button, the following
distance (the distance behind a vehicle
detected ahead of you) setting cycles through
extra long, long, middle, and short following
distances.
382
uuWhen DrivinguAdaptive Cruise Control (ACC)*
Determine the most appropriate following distance setting based on your specific
driving conditions. Be sure to adhere to any following distance requirements set by
local regulation.
The higher your selected set speed is, the greater the short, middle, long or extra
long following distance becomes. See the following examples for your reference.
When the Set Speed is:
Vehicle Distance
50 mph (80 km/h)
65 mph (104 km/h)
84 feet
26 meters
1.1 sec
102 feet
31 meters
1.1 sec
Short
Middle
Long
111 feet
34 meters
1.5 sec
139 feet
43 meters
1.5 sec
155 feet
48 meters
2.1 sec
202 feet
62 meters
2.1 sec
215 feet
66 meters
3.0 sec
285 feet
87 meters
3.0 sec
Extra
Long
Continued
383
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1To Cancel
To Cancel
■
Resuming the prior set speed: After you have
canceled adaptive cruise control, you can resume the
prior set speed while it is still displayed. Press the
RES/+ button when driving at a speed of at least 25
mph (40 km/h) or more.
To cancel adaptive cruise control, do any of
the following:
• Press the CANCEL button.
• Press the MAIN button.
• Depress the brake pedal.
MAIN
Button
CANCEL
Button
•
•
When vehicle speed is less than 25 mph (40km/h).
When the MAIN button is turned off.
■
Automatic cancellation
1Automatic cancellation
The beeper sounds and a message appears on the multi-information display when
ACC is automatically canceled. Any of these conditions may cause the ACC
cancellation:
• Your vehicle speed slows down to 22 mph (35 km/h) and below.
• Bad weather (rain, fog, snow, etc.).
• When the radar sensor inside the front grille gets dirty.
• The vehicle ahead of you cannot be detected.
• An abnormal tire condition is detected, or the tires are skidding.
• Driving on a mountainous road, or driving off road for extended periods.
• Abrupt steering wheel movement.
• When the ABS or VSA® is activated.
• When the ABS or VSA® system indicator comes on.
Even though adaptive cruise control has been
automatically canceled, you can still resume the prior
set speed. Wait until the condition that caused ACC
to cancel improves, then press the RES/+ button.
384
uuWhen DrivinguAdaptive Cruise Control (ACC)*
1To Switch ACC to Cruise Control
To Switch ACC to Cruise Control
■
Always be aware which mode you are in. When you
are driving in Cruise Mode, the system will not assist
you to maintain a following distance from a vehicle
ahead of you.
Press and hold the
(distance) button for one second.
CRUISE MODE SELECTED appears on the multi-information display for two
seconds, and then the mode switches to Cruise.
To switch back to ACC, press and hold the
button again for one second.
Cruise
Control ON
ACC ON
Distance Button
385
uuWhen DrivinguLane Departure Warning (LDW)*
Lane Departure Warning (LDW)*
1Lane Departure Warning (LDW)*
Alerts you when the system determines a possibility of your vehicle unintentionally
crossing over detected lane markings.
Important Safety Reminder
Like all assistance systems, LDW has limitations.
Over-reliance on LDW may result in a collision. It is
always your responsibility to keep the vehicle within
your driving lane.
How the System Works
■
If your vehicle is getting too close to detected
left or right side lane markings without a turn
signal activated, LDW will give audible and
visual alerts.
LDW only alerts you when lane drift is detected
without a turn signal in use. LDW may not detect all
lane markings or lane departures; accuracy will vary
It is always your responsibility to safely operate the
vehicle and avoid collisions.
The beeper sounds and the Lane Departure
message appears on the multi-information
display, letting you know that you need to
take appropriate action.
You can read about handling information for the
camera equipped with this system.
2 Front Sensor Camera* P. 374
1How the System Activates
How the System Activates
■
LDW may automatically shut off and the LDW
indicator comes and stays on.
2 Indicators P. 85
The system begins to search for lane markings when all the following conditions are
met:
• The vehicle is traveling between 45 and 90 mph (72 and 145 km/h).
• The vehicle is on a straight or slightly curved road.
• The turn signals are off.
• The brake pedal is not depressed.
• The wipers are not in continuous operation.
* Not available on all models
386
uuWhen DrivinguLane Departure Warning (LDW)*
LDW On and Off
■
Press the LDW button to turn the system on
and off.
Indicator
u The indicator in the button comes on
when the system is on.
LDW Button
Continued
387
uuWhen DrivinguLane Departure Warning (LDW)*
LDW Limitations
■
LDW may not activate or may not recognize lanes, and may activate even when
keeping in the middle of a lane, under certain conditions. Some examples of these
conditions are listed below.
■
Environmental conditions
• Driving in bad weather (rain, fog, snow, etc.).
• Sudden changes between light and dark, such as an entrance or exit of a tunnel.
• There is little contrast between lane lines and the roadway surface.
• Driving into low sunlight (e.g., at dawn or dusk).
• Strong light is reflected onto the roadway.
• Driving in the shadows of trees, buildings, etc.
• Shadows of adjacent objects are parallel to lane markings.
• Roadway objects or structures are misinterpreted as lane markings.
• Reflections on the interior of the front windshield.
■
Roadway conditions
• Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks,
reflected lights, road spray, high contrast).
• Driving on a road with temporary lane markings.
• Faint, multiple, or varied lane markings are visible on the roadway due to road
repairs or old lane markings.
• The roadway has merging, split, or crossing lines (e.g., such as at an intersection
or crosswalk).
• The lane markings are extremely narrow, wide, or changing.
• The vehicle in front of you is driving near the lane lines.
• The road is hilly or the vehicle is approaching the crest of a hill.
• Driving over bumps.
388
uuWhen DrivinguLane Departure Warning (LDW)*
■
Vehicle conditions
• Headlight lenses are dirty or the headlights are not properly adjusted.
• The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
• The inside of the windshield is fogged.
• The camera temperature gets too hot.
• An abnormal tire or wheel condition (wrong sized, varied size or construction,
improperly inflated, compact spare tire, etc.).
• The vehicle is tilted due to a heavy load or suspension modifications.
389
uuWhen DrivinguLane Keeping Assist System (LKAS)*
Lane Keeping Assist System (LKAS)*
1Lane Keeping Assist System (LKAS)*
Provides steering input to help keep the vehicle in the middle of a detected lane and
provides audible and visual alerts if the vehicle is detected drifting out of its lane.
Important Safety Reminders
The LKAS is for your convenience only. It is not a
substitute for your vehicle control. The system does
not work if you take your hands off the steering
wheel or fail to steer the vehicle.
2 Display Warning and Information
Messages* P. 86
■
Audible and visual alerts
Beeps and a warning display alert
you that the vehicle is drifting out of
a detected lane.
■
Steering input assist
The system applies torque to the
steering to keep the vehicle
■
LKAS camera
between the left and right lane
lines. The applied torque becomes
stronger as the vehicle gets closer to
either of the lane lines.
Monitors the lane
lines
LKAS only alerts you when lane drift is detected
without a turn signal in use. LKAS may not detect all
lane markings or lane departures; accuracy will vary
based on weather, speed, and lane marker condition.
It is always your responsibility to safely operate the
vehicle and avoid collisions.
The LKAS is convenient when it is used on freeways.
LKAS may not work properly under certain
conditions.
2 LKAS Limitations P. 394
When you operate the turn signals to change lanes, the system is suspended, and
resumes after the signals are off.
If you make a lane change without operating the turn signals, the LKAS alerts
activate, and torque is applied to the steering.
* Not available on all models
390
1Lane Keeping Assist System (LKAS)*
When the System can be Used
■
You can read about handling information for the
camera equipped with this system.
2 Front Sensor Camera* P. 374
The system can be used when the following conditions are met.
• The lane in which you are driving has detectable lane markers on both sides, and
your vehicle is in the center of the lane.
• The vehicle speed is between about 45 and 90 mph (72 and 145 km/h).
• You are driving on a straight or slightly curved road.
• The turn signals are off.
If the vehicle drifts toward either left or right lane line
due to the system applying torque, turn off the LKAS
and have your vehicle checked by a dealer.
• The brake pedal is not depressed.
• The wipers are not in continuous operation.
■
How to activate the system
1. Press the MAIN button.
u The LKAS is on in the multi-information
display.
MAIN Button
The system is ready to use.
2. Press the LKAS button.
u Lane outlines appear on the multi-
information display.
LKAS Button
The system is activated.
* Not available on all models
Continued
391
uuWhen DrivinguLane Keeping Assist System (LKAS)*
3. Keep your vehicle near the center of the
1When the System can be Used
lane while driving.
The LKAS temporarily deactivates when it fails to
detect lane lines. When the system detects the lines
again, it comes back on automatically.
u The dotted outer lines change to solid
ones once the system starts operating
after detecting the left and right lane
markings.
1To cancel
To cancel
■
Pressing the MAIN button also turns ACC on and off.
To cancel the LKAS:
Press the MAIN or LKAS button.
The LKAS is turned off every time you stop the
engine, even if you turned it on the last time
you drove the vehicle.
MAIN Button
LKAS Button
392
uuWhen DrivinguLane Keeping Assist System (LKAS)*
■
The system operation is suspended if
you:
• Set the wipers to continuous operation.
u Turning the wipers off resumes the
LKAS.
• Decrease the vehicle speed to about 40
mph (64 km/h) or less.
u Increasing the vehicle speed to about 45
mph (72 km/h) or more resumes the
LKAS.
• Depress the brake pedal.
u The LKAS resumes and starts detecting
the lane lines again once you release the
brake pedal.
When the LKAS is suspended,
the lane lines on the multi-
information display change to
contour lines.
■
The LKAS may automatically be suspended when:
• The system fails to detect lane lines.
• The steering wheel is quickly turned.
• You fail to steer the vehicle.
• The vehicle runs on a curved road over the speed limit.
Once these conditions no longer exist, the LKAS automatically resumes.
■
The LKAS may automatically be canceled when:
• The camera temperature gets too high.
• The camera behind the rearview mirror, or the area around the camera, including
the windshield, gets dirty.
Continued
393
uuWhen DrivinguLane Keeping Assist System (LKAS)*
LKAS Limitations
■
The system may not detect lane markings and therefore may not keep the vehicle in
the middle of a lane under certain conditions, including the following:
■
Environmental conditions
• Driving in bad weather (rain, fog, snow, etc.).
• Sudden changes between light and dark, such as an entrance or exit of a tunnel.
• There is little contrast between lane lines and the roadway surface.
• Driving into low sunlight (e.g., at dawn or dusk).
• Strong light is reflected onto the roadway.
• Driving in the shadows of trees, buildings, etc.
• Shadows of adjacent objects are parallel to lane markings.
• Roadway objects or structures are misinterpreted as lane markings.
• Reflections on the interior of the front windshield.
■
Roadway conditions
• Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks,
reflected lights, road spray, high contrast).
• Driving on a road with temporary lane markings.
• Faint, multiple, or varied lane markings are visible on the roadway due to road
repairs or old lane markings.
• The roadway has merging, split, or crossing lines (e.g., such as at an intersection
or crosswalk).
• The lane markings are extremely narrow, wide, or changing.
• The vehicle in front of you is driving near the lane lines.
• The road is hilly or the vehicle is approaching the crest of a hill.
• Driving over bumps.
394
uuWhen DrivinguLane Keeping Assist System (LKAS)*
■
Vehicle conditions
• Headlight lenses are dirty or the headlights are not properly adjusted.
• The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
• The inside of the windshield is fogged.
• The camera temperature gets too hot.
• An abnormal tire or wheel condition (wrong sized, varied size or construction,
improperly inflated, compact spare tire*, etc.).
• The vehicle is tilted due to a heavy load or suspension modifications.
* Not available on all models
395
uuWhen DrivinguVehicle Stability Assist (VSA®), aka Electronic Stability Control (ESC), System
Vehicle Stability Assist (VSA®), aka Electronic
Stability Control (ESC), System
Helps stabilize the vehicle during cornering if the vehicle turns more or less than
what was intended. It also assists in maintaining traction on slippery surfaces. It does
so by regulating engine output and selectively applying the brakes.
1Vehicle Stability Assist (VSA®), aka Electronic Stability Control
(ESC), System
The VSA® may not function properly if tire types and
size are mixed. Make sure to use the same size and
types of tire, and the air pressures as specified.
VSA® Operation
When the VSA® indicator comes on and stays on
while driving, there may be a problem with the
system. While this may not interfere with normal
driving, have your vehicle checked by a dealer
immediately.
■
When VSA® activates, you may notice that the
engine does not respond to the accelerator.
You may also notice some noise from the
hydraulic system. You will also see the
indicator blink.
VSA® cannot enhance stability in all driving situations
and does not control the entire braking system. You
still need to drive and corner at speeds appropriate
for the conditions and always leave a sufficient
margin of safety.
VSA® System
Indicator
The main function of the VSA® system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.
396
1Vehicle Stability Assist (VSA®), aka Electronic Stability Control
VSA® On and Off
■
(ESC), System
This button is on the driver side control panel.
To partially turn the VSA® features on and off,
press and hold it until you hear a beep.
VSA® OFF Indicator
With the
button pressed, your vehicle will have
normal braking and cornering ability, but VSA®
traction and stability enhancement becomes less
effective.
The traction control stops fully functioning,
allows the wheels to spin more freely at low
speed. The VSA® OFF indicator will also come
on.
In certain unusual conditions when your vehicle gets
stuck in shallow mud or fresh snow, it may be easier
to free it with VSA® temporarily switched off.
When the
button is pressed, the traction control
function becomes less effective. This allows for the
wheels to spin more freely at low speed. You should
only attempt to free your vehicle with the VSA® off if
you are not able to free it when the VSA® is on.
To turn it on again, press the
button until you hear a beep.
(VSA® OFF)
VSA® is turned on every time you start the
engine, even if you turned it off the last time
you drove the vehicle.
Immediately after freeing your vehicle, be sure to
switch VSA® on again. We do not recommend driving
your vehicle with the VSA® system switched off.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
397
uuWhen DrivinguLaneWatchTM
*
LaneWatchTM
*
1LaneWatchTM
*
LaneWatch is an assistance system that allows you to check the passenger side rear
areas displayed on the audio/information screen when the turn signal is activated to
the passenger’s side. A camera in the passenger side door mirror monitors these
areas and allows you to check for vehicle, in addition to your visual check and use of
the passenger door mirror. You can also keep the system on for your convenience
while driving.
3
WARNING
Failure to visually confirm that it is safe to
change lanes before doing so may result in
a crash and serious injury or death.
Do not rely only on LaneWatch while
driving.
1
2
The system activates when you:
The passenger side view
display appears on the
audio/information screen.
Move the turn signal
lever to the passenger
side.
Press the LaneWatch
button.
Always look in your mirrors, to either side
of your vehicle, and behind you for other
vehicles before changing lanes.
Important Safety Reminder
Like all assistance systems, LaneWatch has
limitations. Over reliance on LaneWatch may result in
a collision.
The system deactivates when you:
Pull the turn signal
lever back.
Press the LaneWatch
button again.
The LaneWatch function can be affected by weather,
lighting (including headlights and low sun angle),
ambient darkness, camera condition, and loading.
The LaneWatch may not provide the intended display
of traffic to the side and rear under the following
conditions:
•
Your vehicle’s suspension has been altered,
changing the height of the vehicle.
•
•
Your tires are over or under inflated.
Your tires or wheels are of varied size or construction.
Audio/Information Screen
Camera
* Not available on all models
398
uuWhen DrivinguLaneWatchTM
*
1LaneWatchTM
*
■
Customizing the LaneWatch settings
You can customize the following items using the audio/information screen.
• Show with Turn Signal: Selects whether LaneWatch monitor comes on when
you operate the turn signal light lever.
The LaneWatch camera view is restricted. Its unique
lens makes objects on the screen look slightly
different from what they are.
• Display Time after Turn Off: Changes the remaining Lane Watch display time
after you pull the turn signal lever back.
LaneWatch display does not come on when the shift
lever is in (R
.
• Reference Lines: Selects whether the reference lines appear on the LaneWatch
monitor.
• Next Maneuver Pop up*: Selects whether a turn direction screen of the
navigation system interrupts the LaneWatch display.
• Display: Adjusts display settings.
For proper LaneWatch operation:
•
The camera is located in the passenger side door
mirror. Always keep this area clean. If the camera
Do not cover the camera lens with labels or stickers
of any kind.
•
•
2 Customized Features P. 271
Do not touch the camera lens.
■
Reference Lines
Three lines that appear on the screen can give
an idea of how far the vehicles or objects on
the screen are from your vehicle, respectively.
If an object is near line 1 (in red), it indicates
that it is close to your vehicle whereas an
object near line 3 farther away.
1Reference Lines
The area around the reference line 1 (red) is very close to
your vehicle. As always, make sure to visually confirm
the safety of a lane change before changing lanes.
3
2
The distance between your vehicle and lines 1, 2 and
3 on the screen vary depending on road conditions
and vehicle loading. For example, the reference lines
on the screen may seem to appear closer than the
actual distances when the rear of your vehicle is more
heavily loaded.
1
Consult a dealer if:
•
The passenger side door mirror, or area around it is
severely impacted, resulting in changing the
camera angle.
•
The LaneWatch display does not come on at all.
* Not available on all models
399
uuWhen DrivinguReal Time AWD with Intelligent Control SystemTM
*
Real Time AWD with Intelligent Control SystemTM
*
1Real Time AWD with Intelligent Control SystemTM
*
When the system senses a loss of front wheel traction, it automatically transfers
some power to the rear wheels. This allows you to utilize all available traction and
may increase mobility.
NOTICE
Do not continuously spin the front tires of your
vehicle. Continuously spinning the front tires can
cause transmission or rear differential damage.
You still need to exercise the same care when accelerating, steering, and braking
that you would in a two wheel drive vehicle.
The AWD system may not function properly if tire
type and size are mixed. Make sure to use the same
size and type of tire, and the air pressures as
specified.
If you excessively spin all four wheels and overheat the AWD system, only the front
wheels receive power. Stop until the system cools down.
2 Tire and Wheel Replacement P. 471
* Not available on all models
400
uuWhen DrivinguTire Pressure Monitoring System (TPMS)
1Tire Pressure Monitoring System (TPMS)
Tire Pressure Monitoring System (TPMS)
Instead of directly measuring the pressure in each tire, the TPMS on this vehicle
monitors and compares the rolling radius and rotational characteristics of each
wheel and tire while you are driving to determine if one or more tires are
significantly under-inflated. This will cause the low tire pressure/TPMS indicator to
come on and a message to appear on the multi-information display*.
The system does not monitor the tires when driving
at low speed.
Conditions such as low ambient temperature and
altitude change directly affect tire pressure and can
trigger the low tire pressure/TPMS indicator to come on.
TPMS Calibration
■
Tire pressure checked and inflated in:
You must start TPMS calibration every time you:
• Adjust the pressure in one or more tires.
• Rotate the tires.
• Replace one or more tires.
u Before calibrating the TPMS, turn the ignition switch to ON (w*1, and make
sure that the vehicle is at a complete stop.
•
Warm weather can become under-inflated in
colder weather.
•
Cold weather can become over-inflated in warmer
weather.
The low tire pressure indicator will not come on as a
result of over inflation.
Models with information display
The TPMS may not function properly if tire type and
size are mixed. Make sure to use the same size and
type of tire.
Low Tire Pressure/
TPMS Indicator
Press and hold the TPMS button.
u The low tire pressure/TPMS indicator
blinks a few times.
2 Checking and Maintaining Tires P. 465
TPMS
Button
The low tire pressure/TPMS indicator may come on
with a delay or may not come on at all when:
If the indicator does not blink a few times, the
calibration is not successful. Press and hold
the TPMS button again.
•
You rapidly accelerate, decelerate, or turn the
steering wheel.
•
•
You drive on snowy or slippery roads.
Snow chains are used.
The low tire pressure/TPMS indicator may come on
under the following conditions:
•
•
A compact spare tire is used.
There is a heavier and uneven load on the tires,
such as when towing a trailer, than the condition at
calibration.
*1: Models with the smart entry system have an ENGINE START/STOP button
instead of an ignition switch.
•
Snow chains are used.
* Not available on all models
Continued
401
uuWhen DrivinguTire Pressure Monitoring System (TPMS)
Models with multi-information display
1TPMS Calibration
You can calibrate the system from the customized features on the multi-information
display.
•
TPMS cannot be calibrated if a compact spare tire is
installed.
•
The calibration process requires approximately 30
minutes of cumulative driving at speeds between
30-60 mph (48-97 km/h).
During this period, if the ignition is turned on*1 and
the vehicle is not moved within 45 seconds, you
may notice the low tire pressure indicator comes on
briefly. This is normal and indicates that the
calibration process is not yet complete.
1. Press
button.
2. Press the SEL/RESET button.
u The display switches to the customization setup screen, where you can select
Cancel or Calibrate.
3. Press the
button to select TPMS CALIBRATION, then press the SEL/RESET
•
button and select Calibrate, then press the SEL/RESET button.
u Calibration Started screen appears, then the display returns to the
customization menu screen.
If the snow chains are installed, remove them before
calibrating the TPMS.
If the Calibration Failed to Start message appears, repeat steps 2-3.
If the low tire pressure/TPMS indicator comes on even
when the properly inflated specified regular tires are
installed, have the vehicle checked by a dealer.
We recommend that the tires be replaced with the
same brand, model, and size as the originals. Ask a
dealer for details.
*1: Models with the smart entry system have an
ENGINE START/STOP button instead of an ignition
switch.
402
uuWhen DrivinguTire Pressure Monitoring System (TPMS) - Required Federal Explanation
U.S. models
Tire Pressure Monitoring System (TPMS) - Required
Federal Explanation
Each tire, including the spare (if provided), should be checked
monthly when cold and inflated to the inflation pressure
recommended by the vehicle manufacturer on the vehicle placard
or tire inflation pressure label.
(If your vehicle has tires of a different size than the size indicated
on the vehicle placard or tire inflation pressure label, you should
determine the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with
a tire pressure monitoring system (TPMS) that illuminates a low
tire pressure telltale
when one or more of your tires is significantly under-inflated.
Accordingly, when the low tire pressure telltale illuminates, you
should stop and check your tires as soon as possible, and inflate
them to the proper pressure.
Driving on a significantly under-inflated tire causes the tire to
overheat and can lead to tire failure. Under-inflation also reduces
fuel efficiency and tire tread life, and may affect the vehicle's
handling and stopping ability.
Continued
403
uuWhen DrivinguTire Pressure Monitoring System (TPMS) - Required Federal Explanation
Please note that the TPMS is not a substitute for proper tire
maintenance, and it is the driver’s responsibility to maintain
correct tire pressure, even if under-inflation has not reached the
level to trigger illumination of the TPMS low tire pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction
indicator to indicate when the system is not operating properly.
The TPMS malfunction indicator is combined with the low tire
pressure telltale. When the system detects a malfunction, the
telltale will flash for approximately one minute and then remain
continuously illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the malfunction exists.
When the malfunction indicator is illuminated, the system may
not be able to detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of reasons, including
the installation of replacement or alternate tires or wheels on the
vehicle that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure that the
replacement or alternate tires and wheels allow the TPMS to
continue to function properly.
404
Braking
Brake System
1Parking Brake
Parking Brake
■
NOTICE
Use the parking brake to keep the vehicle stationary when parking.
Release the parking brake fully before driving. The
rear brakes and axle can be damaged if you drive
with the parking brake applied.
To apply:
Depress the parking brake pedal down with
your foot.
If you start driving without fully releasing the parking
brake, a buzzer sounds as a warning.
Always apply the parking brake when parking.
To release:
1. Depress the brake pedal.
2. Depress the parking brake.
Continued
405
uuBrakinguBrake System
1Foot Brake
Foot Brake
■
Check the brakes after driving through deep water,
or if there is a buildup of road surface water. If
necessary, dry the brakes by lightly depressing the
pedal several times.
the stopping force when you depress the brake pedal hard in an emergency
situation. The anti-lock brake system (ABS) helps you retain steering control when
braking very hard.
If you hear a continuous metallic friction sound when
applying the brakes, the brake pads need to be
replaced. Have the vehicle checked by a dealer.
2 Brake Assist System P. 408
2 Anti-lock Brake System (ABS) P. 407
Constantly using the brake pedal while going down a
long hill builds up heat, which reduces the brake
effectiveness. Apply engine braking by taking your
foot off the accelerator pedal and downshifting to a
lower gear.
Do not rest your foot on the brake pedal while
driving, as it will lightly apply the brakes and cause
them to lose effectiveness over time and reduce pad
life. It will also confuse drivers behind you.
406
uuBrakinguAnti-lock Brake System (ABS)
Anti-lock Brake System (ABS)
Helps prevent the wheels from locking up, and helps you retain steering control by
pumping the brakes rapidly, much faster than you.
1Anti-lock Brake System (ABS)
NOTICE
The ABS may not function correctly if you use an
incorrect tire type and size.
The electronic brake distribution (EBD) system, which is part of the ABS, also
balances the front-to-rear braking distribution according to vehicle loading.
When the ABS indicator comes on while driving,
there may be a problem with the system.
While normal braking is not affected, there is a
possibility of the ABS not operating. Have the vehicle
checked by a dealer immediately.
You should never pump the brake pedal. Let the ABS work for you by always
keeping firm, steady pressure on the brake pedal. This is sometimes referred to as
“stomp and steer.“
■
ABS operation
The ABS does not reduce the time or distance it takes
to stop the vehicle. It only helps with steering control
during hard braking.
The brake pedal may pulsate slightly when the ABS is working. Keep holding the
pedal firmly down. On dry pavement, you need to press on the brake pedal very
hard before the ABS activates. However, you may feel the ABS activate immediately
if you are trying to stop on snow or ice.
In the following cases, your vehicle may need more
stopping distance than a vehicle without the ABS:
•
When driving on rough road surfaces, including
when driving on uneven surfaces, such as gravel or
snow.
When the vehicle speed goes under 6 mph (10 km/h), the ABS stops.
•
When tire chains are installed.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
407
uuBrakinguBrake Assist System
Brake Assist System
Designed to assist the driver by generating greater braking force when you depress
the brake pedal hard during emergency braking.
■
Brake assist system operation
Depress the brake pedal firmly for more powerful braking.
When brake assist operates, the pedal may wiggle slightly and an operating noise
may be heard. This is normal. Keep holding the brake pedal firmly down.
408
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
Collision Mitigation Braking SystemTM (CMBSTM)*
Can assist you when there is a possibility of your vehicle colliding with a vehicle or a
pedestrian detected in front of yours. The CMBSTM is designed to alert you when a
potential collision is determined, as well as to reduce your vehicle speed when a
collision is deemed unavoidable to help minimize collision severity.
1Collision Mitigation Braking SystemTM (CMBSTM
)
*
Important Safety Reminder
The CMBSTM is designed to reduce the severity of an
unavoidable collision. It does not prevent collision nor
stop the vehicle automatically. It is still your
responsibility to operate the brake pedal and steering
wheel appropriately according to the driving
conditions.
■
How the system works
When to use
The CMBSTM may not activate or may not detect a
vehicle in front of your vehicle under certain
conditions:
The camera is
located behind the
rearview mirror.
2 CMBSTM Conditions and Limitations P. 414
You can read about handling information for the
camera equipped with this system.
2 Front Sensor Camera* P. 374
The radar sensor is
in the front grille.
The system starts monitoring the roadway ahead when your vehicle speed is about
3 mph (5 km/h) and there is a vehicle in front of you.
The CMBSTM activates when:
●
The speed difference between your vehicle and a vehicle or pedestrian
detected in front of you becomes about 3 mph (5 km/h) and over with a chance
of a collision.
Your vehicle speed is about 62 mph (100 km/h) or less and there is a chance of a
●
collision with an oncoming detected vehicle or a pedestrian in front of you.
* Not available on all models
Continued
409
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
■
When the system activates
1When the system activates
The camera in the CMBSTM is also designed to detect
pedestrians.
The system provides visual and audible alerts of a possible collision, and stops
if the collision is avoided.
However, this pedestrian detection feature may not
activate or may not detect a pedestrian in front of
your vehicle under certain conditions.
Refer to the ones indicating the pedestrian detection
limitations from the list.
u Take appropriate action to prevent a collision (apply the brakes, change
lanes, etc.)
Visual Alerts
Beep
2 CMBSTM Conditions and Limitations P. 414
Audible Alert
At system’s earliest collision alert stage, you can change the distance (LONG/
NORMAL/SHORT) between vehicles at which alerts will come on through multi-
information display setting options.
2 List of customizable options P. 104, 118
410
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
Collision Alert Stages
■
The system has three alert stages for a possible collision. However, depending on circumstances, the CMBSTM may not go through all of
the stages before initiating the last stage.
CMBSTM
Distance between vehicles
The radar sensor detects
Audible & Visual WARNINGS
Braking
a vehicle
Normal
Long Short
When in Long, visual and audible alerts come
on at a longer distance from a vehicle ahead
than in NORMAL setting, and in SHORT, at a
shorter distance than in NORMAL.
Vehicle
Ahead
There is a risk of a collision
with the vehicle ahead of
you.
Stage
one
—
Your Vehicle
The risk of a collision has
increased, time to respond
is reduced.
Your
Vehicle
Vehicle
Ahead
Stage
two
Lightly applied
Visual and audible alerts.
The CMBSTM determines
that a collision is
unavoidable.
Your
Vehicle
Vehicle
Ahead
Stage
three
Forcefully applied
Continued
411
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
1Collision Mitigation Braking SystemTM (CMBSTM
)
*
CMBSTM On and Off
■
The CMBSTM may automatically shut off, and the
CMBSTM indicator will come and stay on under certain
conditions.
Press this button for about one second to turn
the system on and off.
2 CMBSTM Conditions and Limitations P. 414
When the CMBSTM is off:
• The beeper sounds.
• The CMBSTM indicator in the instrument
panel comes on.
• A message on the multi-information display
reminds you that the system is off.
The CMBSTM is in the previously selected ON or
OFF setting each time you start the engine.
* Not available on all models
412
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
1Collision Mitigation Braking SystemTM (CMBSTM
)
*
With Little Chance of a Collision
The CMBSTM may activate even when you are aware of a vehicle ahead of you, or
■
Avoid the following conditions that may cause the
radar aim to be temporarily out of range and prevent
the CMBSTM from working properly.
when there is no vehicle ahead. Some examples of this are:
•
A heavy load in the rear or modifications to the
suspension tilts your vehicle.
■
When Passing
•
The tire pressures are not correct, the tire sizes are
incorrect, the tire types are different, and/or the
tires are not in good condition.
Your vehicle approaches another vehicle ahead of you and you change lanes to pass.
■
At an intersection
Your vehicle approaches or passes another vehicle that is making a left or right turn.
For the CMBSTM to work properly:
Always keep the radar sensor cover clean.
■
On a curve
When driving through curves, your vehicle comes to a point where an oncoming
vehicle is right in front of you.
Never use chemical solvents or polishing powder for
cleaning the sensor cover. Clean it with water or a
mild detergent.
■
Through a low bridge at high speed
You drive under a low or narrow bridge at high speed.
Do not put a sticker on the emblem or replace the
emblem.
■
Speed bumps, road work sites, train tracks, roadside objects, etc.
If you need the radar sensor to be repaired, or
removed, or the radar sensor cover is strongly
impacted, turn off the system by pressing the
CMBSTM off button and take your vehicle to a dealer.
You drive over speed bumps, steel road plates, etc., or your vehicle approaches train
tracks or roadside objects [such as a traffic sign and guard rail] on a curve or, when
parking, stationary vehicles and walls.
* Not available on all models
Continued
413
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
CMBSTM Conditions and Limitations
■
The system may automatically shut off and the CMBSTM indicator will come on under
certain conditions. Some examples of these conditions are listed below. Other
conditions may reduce some of the CMBSTM functions.
2 Front Sensor Camera* P. 374
■
Environmental conditions
• Driving in bad weather (rain, fog, snow, etc.).
• Sudden changes between light and dark, such as an entrance or exit of a tunnel.
• There is little contrast between objects and the background.
• Driving into low sunlight (e.g., at dawn or dusk).
• Strong light is reflected onto the roadway.
• Driving in the shadows of trees, buildings, etc.
• Roadway objects or structures are misinterpreted as vehicles and pedestrians.
• Reflections on the interior of the front windshield.
■
Roadway conditions
• Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks,
reflected lights, road spray, high contrast).
■
Vehicle conditions
• Headlight lenses are dirty or the headlights are not properly adjusted.
• The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
• The inside of the windshield is fogged.
• An abnormal tire or wheel condition (wrong sized, varied size or construction,
improperly inflated, compact spare tire, etc.).
• The vehicle is tilted due to a heavy load or suspension modifications.
• The camera temperature gets too hot.
* Not available on all models
414
uuBrakinguCollision Mitigation Braking SystemTM (CMBSTM
)
*
• Driving with the parking brake applied.
• When the radar sensor in the front grille gets dirty.
■
Detection limitations
• A vehicle or pedestrian suddenly crosses in front of you.
• The distance between your vehicle and the vehicle or pedestrian ahead of you is
too short.
• A vehicle cuts in front of you at a slow speed, and it brakes suddenly.
• When you accelerate rapidly and approach the vehicle or pedestrian ahead of you
at high speed.
• The vehicle ahead of you is a motorcycle, bicycle, mobility scooter or other small
vehicle.
• When there are animals in front of your vehicle.
• When you drive on a curved, winding or undulating road that makes it difficult for
the sensor to properly detect a vehicle in front of you.
• The speed difference between your vehicle and a vehicle in front of you is
significantly large.
• An oncoming vehicle suddenly comes in front of you.
• Your vehicle abruptly crosses over in front of an oncoming vehicle.
• When driving through a narrow iron bridge.
Limitations applicable to pedestrian detection only
• When there is a group of people in front of your vehicle walking together side by
side.
• Surrounding conditions or belongings of the pedestrian alter the pedestrian’s
shape, preventing the system from recognizing that the person is a pedestrian.
• When the pedestrian is squatting.
• When the pedestrian is shorter than about 3.3 feet (1 meter) or taller than about
6.6 feet (2 meters) in height.
415
Parking Your Vehicle
When Stopped
1. Depress the brake pedal firmly with the shift lever in (D
2. Firmly apply the parking brake.
.
Do not park your vehicle near flammable objects,
such as dry grass, oil, or timber.
Heat from the exhaust can cause a fire.
3. Move the shift lever from (D to (P
4. Turn off the engine.
.
Always set the parking brake firmly, in particular if you are parked on an incline.
1When Stopped
NOTICE
The following can damage the transmission:
•
•
•
Depressing the accelerator and brake pedals
simultaneously.
Holding the vehicle in place when facing uphill by
depressing the accelerator pedal.
Moving the shift lever into (P before the vehicle
stops completely.
Raise the wiper arms when snow is expected.
416
Multi-View Rear Camera*
About Your Multi-View Rear Camera
Models with one display
1About Your Multi-View Rear Camera
The intelligent multi-information display (i-MID) can display your vehicle’s rear view.
The display automatically changes to the rear view when the shift lever is moved to
The rear camera view is restricted. You cannot see
the corner ends of the bumper or what is underneath
the bumper. Its unique lens also makes objects
appear closer or farther than they actually are.
(R
.
Models with two displays/Models with navigation system
See the Navigation System Manual.
Visually confirm that it is safe to drive before backing
up. Certain conditions, such as weather, lighting, and
high temperatures, may also restrict the rear view. Do
not rely on the rearview display which does not give
you all information about conditions at the back of
your vehicle.
Models with two displays/Models without navigation system
The audio/information screen can display your vehicle’s rear view. The display
automatically changes to the rear view when the shift lever is moved to (R
.
If the camera lens is covered with dirt or moisture,
use a soft, moist cloth to keep the lens clean and free
of debris.
* Not available on all models
Continued
417
uuMulti-View Rear Camera*uAbout Your Multi-View Rear Camera
1About Your Multi-View Rear Camera
Multi-View Rear Camera Display Area
■
You can change the Fixed Guideline and Dynamic
Guideline settings.
2 Customized Features P. 271
Wide View Mode
Guidelines
Bumper
Models with two displays/Models without navigation
system
Fixed Guideline
Normal View Mode
On: Guidelines appear when you shift into (R
Off: Guidelines do not appear.
Dynamic Guideline
On: Guidelines move according to the steering wheel
direction.
.
Camera
Tailgate Open Range
Top Down View Mode
Approx. 39 inches (1 m)
Approx. 79 inches (2 m)
Approx. 118 inches (3 m)
Off: Guidelines do not move.
418
uuMulti-View Rear Camera*uAbout Your Multi-View Rear Camera
You can view three different camera angles on the rearview display.
Models with one display
Press the selector knob to switch the angle.
Models with two displays/Models without navigation system
Touch the appropriate icon to switch the angle.
: Wide view
: Normal view
: Top down view
All models
If the last used viewing mode is Wide or Normal, the same mode is selected the next
time you shift into (R. If Top View is last used before you turned off the engine,
Wide mode is selected next time you turn the ignition switch to ON (w*1 and shift
to (R
.
*1: Models with the smart entry system have an ENGINE START/STOP button
instead of an ignition switch.
419
Refueling
Fuel Information
■
Fuel recommendation
1Fuel Information
Unleaded gasoline, pump octane number 87 or higher
NOTICE
We recommend quality gasoline containing
detergent additives that help prevent fuel system and
engine deposits. In addition, in order to maintain
good performance, fuel economy, and emissions
control, we strongly recommend the use of gasoline
that does NOT contain harmful manganese-based
fuel additives such as MMT, if such gasoline is
available.
Use of lower octane gasoline can cause a persistent, heavy metallic knocking noise
that can lead to engine damage.
■
Top tier detergent gasoline
Because the level of detergency and additives in gasoline vary in the market, Honda
endorses the use of “TOP TIER Detergent Gasoline” where available to help
maintain the performance and reliability of your vehicle. TOP TIER Detergent
Gasoline meets a new gasoline standard jointly established by leading automotive
manufacturers to meet the needs of today’s advanced engines.
Use of gasoline with these additives may adversely
affect performance, and cause the malfunction
indicator lamp on your instrument panel to come on.
If this happens, contact a dealer for service.
Qualifying gasoline retailers will, in most cases, identify their gasoline as having met
“TOP TIER Detergent Gasoline” standards at the retail location. This fuel is
guaranteed to contain the proper level of detergent additives and be free of metallic
additives. The proper level of detergent additives, and absence of harmful metallic
additives in gasoline, help avoid build-up of deposits in your engine and emission
control system.
Some gasoline today is blended with oxygenates such
as ethanol. Your vehicle is designed to operate on
oxygenated gasoline containing up to 15% ethanol
by volume. Do not use gasoline containing methanol.
If you notice any undesirable operating symptoms, try
another service station or switch to another brand of
gasoline.
For further important fuel-related information for your vehicle, or on information on
www.honda.ca for additional information on gasoline. For more information on top
420
uuRefuelinguHow to Refuel
■
Fuel tank capacity: 15.3 US gal (58 liters)
1How to Refuel
How to Refuel
1. Stop your vehicle with the service station
pump on the left side of the vehicle in the
rear.
3
WARNING
Gasoline is highly flammable and explosive.
You can be burned or seriously injured
when handling fuel.
2. Turn off the engine.
Pull
3. Pull on the fuel fill door release handle
under the lower left corner of the
dashboard.
• Stop the engine, and keep heat, sparks,
and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
u The fuel fill door opens.
Continued
421
uuRefuelinguHow to Refuel
4. Remove the fuel fill cap slowly. If you hear a
release of air, wait until this stops, then turn
the knob slowly to open the fuel fill cap.
1How to Refuel
The filler nozzle automatically stops to leave space in
the fuel tank so that fuel does not overflow as a result
of changes in air temperature.
If the filler nozzle keeps turning off when the tank is
not full, there may be a problem with the pump's fuel
vapor recovery system. Try filling at another pump. If
this does not fix the problem, consult a dealer.
Cap
Cap
5. Place the fuel fill cap in the holder.
6. Insert the fuel filler nozzle fully.
u When the tank is full, the filler nozzle will
click off automatically. This leaves space
in the fuel tank in case the fuel expands
with a change in the temperature.
7. After filling, replace the fuel fill cap,
tightening it until you hear it click at least
once.
Do not continue to add fuel after the filler nozzle has
automatically stopped. Additional fuel can exceed
the full tank capacity.
Holder
u Shut the fuel fill door by hand.
422
Fuel Economy
Improving Fuel Economy
Fuel economy depends on several conditions, including driving conditions, your
driving habits, the condition of your vehicle, and loading. Depending on these and
other conditions, you may or may not achieve the rated fuel economy of this vehicle.
1Improving Fuel Economy
Direct calculation is the recommended method to
determine actual fuel consumed while driving.
Gallons of
fuel
Miles per
Gallon
Miles driven
100
Maintenance and Fuel Economy
■
Kilometers
L per 100 km
Liter
You can optimize your fuel economy with proper maintenance of your vehicle.
Always maintain your vehicle in accordance with the messages displayed on the
information display*/multi-information display*/intelligent multi-information display
(i-MID).
• Use the recommended viscosity engine oil, displaying the API Certification Seal.
• Maintain the specified tire pressure.
In Canada, posted fuel economy numbers are
established following a simulated test. For more
information on how this test is performed, please visit
• Do not load the vehicle with excess cargo.
• Keep your vehicle clean. A buildup of snow or mud on your vehicle's underside
adds weight and increases wind resistance.
* Not available on all models
423
Accessories and Modifications
Accessories
When installing accessories, check the following:
1Accessories and Modifications
• Do not install accessories on the windshield. They can obstruct your view and
delay your reaction to driving conditions.
3
WARNING
• Do not install any accessories over areas marked SRS Airbag, on the sides or backs
of the front seats, on front or side pillars, or near the side windows. Accessories
installed in these areas may interfere with proper operation of the vehicle’s
airbags or may be propelled into you or another occupant if the airbags deploy.
• Be sure electronic accessories do not overload electrical circuits or interfere with
proper operation of your vehicle.
Improper accessories or modifications can
affect your vehicle's handling, stability, and
performance, and cause a crash in which
you can be seriously hurt or killed.
Follow all instructions in this owner's
manual regarding accessories and
modifications.
2 Fuses P. 503
• Before installing any electronic accessory, have the installer contact a dealer for
assistance. If possible, have a dealer inspect the final installation.
Honda Genuine accessories are recommended to
ensure proper operation on your vehicle.
Modifications
Do not modify your vehicle or use non-Honda components that can affect its
handling, stability, and reliability.
Overall vehicle performance can be affected. Always make sure all equipment is
properly installed and maintained, and that it meets federal, state, province,
territory, and local regulations.
424
