Deutsch
EnglishInterior equipment -> Universal Integrated Remote Control for your BMW 6 Series 2011-2017
Controls
Interior equipment
Interior equipment
Compatibility
Vehicle features and options
If this symbol is printed on the packag‐
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems. The respectively applicable country
provisions must be observed when using the
respective features and systems.
ing or in the instructions of the system
to be controlled, the system is gener‐
ally compatible with the universal garage door
opener.
If you have any questions, please contact:
▷
▷
Your service center.
HomeLink is a registered trademark of Gentex
Corporation.
Universal Integrated Remote
Control
Control elements on the interior
rearview mirror
The concept
The universal garage door opener can operate
up to 3 functions of remote-controlled sys‐
tems such as garage door drives or lighting
systems. The universal garage door opener re‐
places up to 3 different hand-held transmitters.
To operate the remote control, the buttons on
the interior rearview mirror must be program‐
med with the desired functions. The hand-held
transmitter for the particular system is required
in order to program the remote control.
▷
▷
▷
LED, arrow 1.
Buttons, arrow 2.
During programming
The hand-held transmitter, arrow 3, is re‐
quired for programming.
During programming and before activat‐
ing a device using the universal garage door
opener, ensure that there are no people, ani‐
mals or objects in the area of the remote-con‐
trolled device; otherwise, there is a risk of in‐
jury or damage.
Programming
General information
1. Switch on the ignition.
2. Initial setup:
Also follow the safety instructions of the hand-
held transmitter.◀
Press and hold the left and right button on
the interior rearview mirror simultaneously
for approximately 20 seconds until the LED
on the interior rearview mirror flashes. This
Before selling the vehicle, delete the stored
functions for the sake of security.
170
Interior equipment
Controls
erases all programming of the buttons on
the interior rearview mirror.
rearview mirror starts flashing rapidly and then
stays lit constantly for 2 seconds, the system
features an alternating-code system. Flashing
and continuous illumination of the LED will re‐
peat for approximately 20 seconds.
3. Hold the hand-held transmitter for the sys‐
tem to be controlled approx. 1 to 3 in/2.5 to
8 cm away from the buttons of the interior
rearview mirror. The required distance de‐
pends on the manual transmitter.
For systems with an alternating-code system,
the universal garage door opener and the sys‐
tem also have to be synchronized.
4. Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program‐
med on the interior rearview mirror. The
LED on the interior rearview mirror will be‐
gin flashing slowly.
Please read the operating manual to find out
how to synchronize the system.
Synchronizing is easier with the aid of a sec‐
ond person.
To synchronize:
5. Release both buttons as soon as the LED
flashes more rapidly. The LED flashing
faster indicates that the button on the inte‐
rior rearview mirror has been programmed.
1. Park the vehicle within range of the re‐
mote-controlled system.
2. Program the relevant button on the interior
rearview mirror as described.
If the LED does not flash faster after at
least 60 seconds, change the distance be‐
tween the interior rearview mirror and the
hand-held transmitter and repeat the step.
Several more attempts at different distan‐
ces may be necessary. Wait at least
15 seconds between attempts.
3. Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.
4. Hold down the programmed button on the
interior rearview mirror for approximately
3 seconds and then release it. If necessary,
repeat this step up to three times in order
to finish synchronization. Once synchroni‐
zation is complete, the programmed func‐
tion will be carried out.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the
hand-held transmitter button for 2 sec‐
onds.
Reprogramming individual buttons
6. To program other functions on other but‐
tons, repeat steps 3 to 5.
1. Switch on the ignition.
2. Press and hold the interior rearview mirror
button to be programmed.
The systems can be controlled using the inte‐
rior rearview mirror buttons.
3. As soon as the interior rearview mirror LED
starts flashing slowly, hold the hand-held
transmitter for the system to be controlled
approx. 1 to 3 in/2.5 to 8 cm away from the
buttons of the interior rearview mirror. The
required distance depends on the manual
transmitter.
Special feature of the alternating-
code wireless system
If you are unable to operate the system after
repeated programming, please check if the
system to be controlled features an alternat‐
ing-code system.
Read the system's operating manual, or press
the programmed button on the interior rear‐
view mirror longer. If the LED on the interior
171
Controls
Interior equipment
4. Likewise, press and hold the button of the
desired function on the hand-held trans‐
mitter.
proximately 20 seconds until the LED flashes
rapidly. All stored functions are deleted. The
functions cannot be deleted individually.
5. Release both buttons as soon as the inte‐
rior rearview mirror LED flashes more rap‐
idly. The LED flashing faster indicates that
the button on the interior rearview mirror
has been programmed. The system can
then be controlled by the button on the in‐
terior rearview mirror.
Sun visor
Glare shield
Fold the sun visor down or up.
Vanity mirror
If the LED does not flash faster after at
least 60 seconds, change the distance and
repeat the step. Several more attempts at
different distances may be necessary. Wait
at least 15 seconds between attempts.
A vanity mirror is located in the sun visor be‐
hind a cover. When the cover is opened, the
mirror lighting switches on.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the
hand-held transmitter button for 2 sec‐
onds.
Ashtray/cigarette lighter
Steptronic transmission: open
Controls
Before operation
Before operating a system using the uni‐
versal garage door opener, ensure that there
are no people, animals, or objects within the
range of movement of the remote-controlled
system; otherwise, there is a risk of injury or
damage.
Press button.
Also follow the safety instructions of the hand-
held transmitter.◀
Emptying
Take out the insert.
The system, such as the garage door, can be
operated using the button on the interior rear‐
view mirror while the engine is running or when
the ignition is started. To do this, hold down
the button within receiving range of the system
until the function is activated. The interior rear‐
view mirror LED stays lit while the wireless sig‐
nal is being transmitted.
Lighter
Push in the lighter.
The lighter can be removed as
soon as it pops back out.
Danger of burns
Deleting stored functions
Press and hold the left and right button on the
interior rearview mirror simultaneously for ap‐
Only hold the hot lighter by its knob; oth‐
erwise, there is a danger of getting burned.
172
